28 July 2025 in IEEE Microwave and Wireless Technology Letters
This article presents a 6–8-GHz fractional-N charge-pump-phase-lock-loop (CP-PLL) working down to 3.5 K temperature in 28-nm bulk CMOS for quantum computing. To accommodate the wide operating temperature and frequency tuning ranges, a self-biased current source calibration method is introduced to maintain a constant charge pump bias current, thereby ensuring adequate phase margin and minimizing phase noise. An automatic flicker noise calibration technique is also employed to mitigate flicker noise degradation, while a sampled loop filter is utilized to reduce spur degradation at cryogenic temperatures. Owing to these methods, this phase-lock loop (PLL) achieves a phase noise of −90 dBc/Hz at 10 kHz and a jitter of 445 fs at cryogenic temperature while using a power consumption of 4.93 mW. The reference spur is below −70 dB although the mismatch of charge pump degrades at least $2\times $ at cryogenic temperature.
26 May 2025 in IEEE Microwave and Wireless Technology Letters
A cryogenic low-voltage, broadband low-noise amplifier(LNA) has been designed for qubit state readout systems. The proposed LNA utilizes passive components for noise cancellation. A tri-coupled transformer is utilized to simultaneously achieve broadband input impedance matching and noise matching. Additionally, it incorporates capacitive feedback and an in-phase transformer to effectively cancel noise. Implemented in 28-nm bulk CMOS technology and verified at 10 K, the LNA achieves a maximum gain of 26.7 dB, a −3-dB bandwidth of 2.2 GHz, a lowest noise temperature (NT) of 25 K, a power consumption of 4.05 mW at 0.6-V supply voltage, and a figure of merit (FoM) of 0.12 dB/mW/ph, which is comparable with the recent works.
27 May 2026 in IEEE Journal of Solid-State Circuits
This article presents a cryogenic quantum interface chipset at 3.5 K for superconducting transmon qubit operations. The chipset comprises a phase-detection readout and a phase-shifter-based polar-modulation controller with flexible scalability. With the proposed phase-detection readout scheme, a 9-bit time-to-digital converter (TDC)-based state detector is used to read out the qubit state by detecting the phase difference between the stimulus signal and the reflected signal. A low-IF N-path filter-based receiver and a multi-tone transmitter are co-designed to enable frequency-division multiplexing (FDM) dispersive readout of multiple qubits. A phase-shifter-based polar-modulation XY-driver is developed with support for fast phase quantum gate operation and derivative-removal-by-adiabatic-gate (DRAG) pulse generation. The Z-driver is realized using a static digital-to-analog converter (DAC) array and a 10-bit dynamic DAC for power efficiency. Fabricated in a 28-nm bulk CMOS process, the chipset occupies a die area of 4.6 mm2. The readout RX achieves a noise temperature of 40 K with a gain of 45–83 dB and a bandwidth of 1.2 GHz. The readout RX consumes 32% less power than state-of-the-art designs. The measured total readout power for simultaneous detection of two qubits is 12.2 mW, which is the lowest among readouts with a similar integration level. In addition, the controller achieves a spurious-free dynamic range (SFDR) of 49 dB for a 1-GS/s Z-driver and an SNR of 42 dB for a 1-GS/s XY-driver. The XY-driver consumes 4.3 mW per qubit under active control. Verified with practical transmon qubits, the readout fidelity exceeds 92.6%, approaching that of commercial instruments. A Rabi experiment at 5.61/6.36 MHz, a Ramsey experiment at 4.1 MHz, and a T1 experiment at $9.98~{\mu }$ s are also successfully observed using the proposed chipset at 3.5 K.
31 March 2026 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This article presents a cryogenic fractional-N 4–5.9-GHz cascaded phase-locked loop (PLL) operating down to 4 K for a transmon control system. The main PLL stage employs a supply-boost constant charging current sampling phase detector (SBCC-SPD) to achieve ultralow rms jitter and fractional spur from 300 to 4 K. The first-stage PLL operates in integer-N mode employing an inverter-based sampling PD and a Class-F voltage-controlled oscillator (VCO) to achieve low output phase noise, with a frequency-tuning range of 11.8–15.9 GHz. The second-stage PLL operates in fractional-N mode using double-multimodule divider (MMD) with shared delta-sigma-modulator (DSM) architecture. It incorporates an SBCC-SPD and Class-B VCO, with a frequency-tuning range of 4–5.9 GHz for transmon control application. The reference signal of SBCC-SPD is from the divided signal of the first-stage PLL, which is modulated by the same DSM used in the feedback path of the second-stage PLL to compensate for the quantization error. Fabricated in a 28-nm Bulk CMOS process, the PLL achieves an rms jitter of 58.8 fs at 300 K and 36.9 fs at 4 K, with a fractional spur of −71.8 dBc at 300 K and −69.1 dBc at 4 K. The chip consumes a power consumption of 24.8 mW at 300 K and 14.2 mW at 4K corresponding to a figure of merit (FOM) of −257.1 dB. This chip occupies an area of 0.344 mm2.