24 May 2018 in IEEE Transactions on Microwave Theory and Techniques
Radar-absorbing materials are used in stealth technologies for concealment of an object from radar detection. Resistive and/or magnetic composite materials are used to reduce the backscattered microwave signals. However, nontunable characteristics or the required complex structure hampered the application of these materials. Here, multilayer graphene-based frequency selective surfaces (MLGFSS), which reach a size of 150 mm $x$ 150 mm, are designed and fabricated. By properly changing the growth temperature of MLG using the chemical vapor deposition approach and designing the pattern of graphene layer, the impedance matching condition can be satisfied at different frequencies. As a result, two kinds of absorbers with different working bandwidths are realized. The performances of the proposed absorbers are analyzed using full-wave simulation and are also tested with experimental results. Our method of fabricating large-area MLGFSS avoids the direct contact between the stencil mask and graphene, and guarantees the integrity and quality of patterned graphene structure. A good agreement between simulation and measurement results demonstrates that such ultrathin MLGFSS is very useful in the design of graphene-based functional devices at microwave frequencies.
14 October 2021 in IEEE Transactions on Antennas and Propagation
In this article, we demonstrate a flexible and wearable hybrid radio frequency (RF) and solar energy harvesting system for powering wearable electronic devices. The system consists of a flexible transparent antenna, a flexible transparent rectifying circuit, and an amorphous silicon solar cell. By utilizing transparent stacked structure, the rectenna and the solar cell can provide more hybrid output power to accommodate more application scenarios. The flexible transparent antenna shows two impedance matching bandwidths of 3.5–3.578 and 4.79–5.09 GHz, covering n78/n79 fifth-generation (5G) communication frequency band and 5-GHz WiFi frequency band. At the frequency of 3.5 GHz, the flexible transparent rectifying circuit achieves a high RF-to-dc conversion efficiency of 54.67% at 13 dBm RF input power. In the room with a light intensity of 210 lux, compared with a single solar cell, the hybrid energy harvesting system can obtain an additional 35.6%–769.5% output power when the RF source power is varied from 4 to 10 dBm. These results demonstrate that the proposed flexible and wearable RF-solar energy harvester can provide reliable electric power supply, which can be a potential candidate for powering wearable electronic devices, distributed sensors and IOT devices.
27 March 2008 in Microwave and Optical Technology Letters
10 April 2018 in IEEE Transactions on Microwave Theory and Techniques
In this paper, a dynamically tunable substrate-integrated-waveguide (SIW) attenuator using graphene is first presented. Two graphene sandwich structures are placed inside an SIW, which serve as conductivity-tunable E-plane septum. By applying biased voltage to the graphene, the attenuation can be dynamically changed; meanwhile, the reflection can still keep at a relatively low level. A closed form of the attenuation is also proposed, and the mechanism of the attenuator is theoretically analyzed in detail. Furthermore, a prototype operating from 7 to 14.5 GHz has been fabricated and measured. Both the theoretical calculation and the numerical simulation results have a good agreement with the experimental results, which present the attenuation ranges from 2 to 15 dB with a stable 7.5-GHz wideband while the bias voltage changing from 0 to 4 V.
21 February 2024 in Advanced Science
Distributed micro‐energy harvesting devices offer the flexibility, sustainability, and multi‐scenario applicability that will be critical to wearable electronic products in the Internet of Things. The radiofrequency and triboelectric (RF‐TE) hybrid energy harvester (HEH) concept and prototype is presented for the first time, to simultaneously capture the energy from ambient electromagnetic waves and biological motions. The proposed hybrid energy harvesting system consists of a wearable rectenna, a triboelectric nanogenerator (TENG), and a power management circuit (PMC). Among them, the all‐fabric rectenna exhibits good impedance matching characteristics in the ISM frequency. The flexible TENG unit can generate a maximum power density of 0.024 µW cm−2. The designed multifunctional fabric‐based PMC can considerably enhance the controllability of harvested hybrid energy. Additionally, a normalizable fabric circuit board quasi surface mount technology (FCB‐SMT) is proposed to integrate all modules on the same fabric substrate in one step, making the entire system superior mechanical robustness. The proposed wearable fabric‐based RF‐TE hybrid energy harvester is capable of successfully driving consumer electronics (such as sensors, watches, etc.). It provides a new energy solution strategy for self‐powered wearable electronic devices and is anticipated to encourage the efficient utilization of renewable energy.
14 February 2020 in IEEE Transactions on Antennas and Propagation
In this paper, a dynamically tunable graphene-based absorber in Ku band is proposed for the first time, the center frequency of which can be continuously tuned while maintaining an excellent absorption performance. It consists of a periodically patterned graphene sandwich structure (GSS) and periodic patches printed on the substrate backed with ground. The periodically patterned GSS are directly deposited on the top surface of patches. By using the external bias voltage, the proposed absorber can provide a dynamically tunable operating frequency from 13.9GHz to 16.4GHz, in which the absorptions remain above 0.92. To theoretically investigate the performance of the absorber, an equivalent circuit based on transmission-line is derived. We fabricate and measure some samples to experimentally verify the dynamical frequency tunability of the graphene-based absorber, which has never been really achieved before in microwave frequency. A good agreement between simulation and measurement is acquired. The whole thickness of absorber is equal to 0.06λ, which provides a path forward for realization of dynamically tunable and ultra-thin absorber. The design strategy can generally be applied to other wavelength regions applications such as mechanical deformation and bolometric detector.