Department of Technological Equipment, Mechanical Engineering and Standardization, Faculty of Mechanical Engineering, Karaganda Technical University named after Abulkas Saginov, Karaganda, Kazakhstan
Auto-generated profile, based on publicly available information
Baglan Smailova
Department of Technological Equipment, Mechanical Engineering and Standardization, Faculty of Mechanical Engineering, Karaganda Technical University named after Abulkas Saginov, Karaganda, Kazakhstan
This work is devoted to the analysis of the stress-strain state of the surfaced gear teeth using the T-Flex CAD software. The study showed that the surfaced teeth are able to withstand workloads, as well as loads increased by 50%, demonstrating a deformation of only 2%. Zones of maximum stresses and deformations have been identified, which makes it possible to predict the durability and reliability of the surfaced teeth. The conducted studies confirm the effectiveness of the electroslag surfacing method for restoring gears and its application to improve the performance of gears under high loads.
30 December 2024 in Science and Technology of Kazakhstan
The article focuses on the results of a study of the effect of electroslag surfacing modes on the penetration depth of restored teeth, conducted on the basis of a full factorial experiment (FFE) type 22. The welding current and the voltage on the slag bath were selected as factors. Each experiment was repeated three times, and the results were analyzed to build a regression model that takes into account all interactions of factors. The article describes in detail the process of encoding variable factors, constructing a planning matrix, calculating the coefficients of the regression equation and checking them for significance using the Student’s criterion. The adequacy of the experiment was confirmed by calculations using the Fisher criterion (Fcalculated<Ftable). According to the results of the experiment, it was found that the stress on the slag bath has the most significant effect on the total depth of penetration. The optimal mode has been determined (welding current 400 A and voltage on the slag bath 45 V), which provides the required penetration depth (4.63 mm) of a large-modulus tooth. The convergence of the results of the full-scale test with the results of planning a full factor experiment of type 22 was revealed, which made it possible to determine the optimal surfacing mode. This study can be used to optimize the parameters of electroslag surfacing, which will lead to an increase in the quality and efficiency of restoration of worn teeth. Keywords: electroslag surfacing, surfacing mode, penetration depth, welding current, welded tooth.
1 January 2025 in Journal of Applied Engineering Science
The paper focuses on the calculation of cylindrical gear transmissions using analytical and numerical methods to determine contact and bending stresses. The results of analytical calculations are compared with numerical modeling data obtained using the Ansys Workbench software environment. A comparative analysis of the results is conducted, and discrepancies between the calculations are identified. Special attention is given to the analysis of stresses in surfaced gear teeth compared to solid ones. Unlike standard calculations for solid gears, this study focuses on the stress-strain state of surfaced teeth, taking into account their operational properties. For a more detailed analysis, the concept of the 'tooth contact angle position - ps' is introduced, which allowed for an in-depth investigation of its stress-strain state. The obtained results help identify the specific behavior of restored teeth under load, which is particularly relevant for developing gear transmission restoration technologies and assessing their durability. Considering the operational properties of surfaced teeth enables a more accurate evaluation of their strength characteristics. This study is aimed at assessing the strength properties of gear transmissions with surfaced teeth and can be used to optimize their design.
1 January 2025 in Journal of Applied Engineering Science
This study focuses on the restoration of large-module gear teeth of ball mills using the electroslag welding method, with an emphasis on practical results and mathematical modeling. The research established that optimal electroslag welding conditions are achieved by stabilizing key process parameters, such as current strength, slag bath voltage, and cooling water flow rate. For high-quality welding of gear teeth with a module of 20 mm, the following parameters are recommended: current strength I=362.5 A, slag bath voltage U=73.25-74 V, and water flow rate Qw=3-3.5 l/min. These parameters ensure minimal roughness and the required hardness of the welded teeth. Mathematical modeling provided equations linking welding modes with the roughness and hardness of the welded teeth. The presented experimental data are highly relevant for the scientific community and enterprises involved in the restoration of large-module gear wheels. The results hold significant practical value as they enable enterprises to reduce restoration costs and enhance the durability of components.
30 September 2024 in Science and Technology of Kazakhstan
This study examines the quality of a gear tooth surface fragment restored through electric arc welding. Visual inspection revealed a defect-free, dense surface. Macrostructure examination displayed uniformity and absence of cracks in the metal sample. The high hardness (HRC-36.61) of the weld deposit is crucial for wear resistance, while the base metal, with lower hardness (HRC-29.09), ensures ductility and impact toughness. Martensitic and residual austenitic structures in the weld deposit indicate deformation-resistant properties, with austenite providing good ductility and martensite contributing to high hardness and strength, making the material resistant to wear and deformation under dynamic loads. Thin lens-like martensitic plates and a reed-like structure suggest unique formation characteristics during electroslag welding’s oxidizing-reducing reactions. Microstructure analysis revealed a finer structure in the weld deposit compared to the base metal. The base metal exhibited a ferrite-pearlite structure typical of many steels, unchanged after welding. The weld deposit showed elevated carbon (0.70 %) and manganese (1.38 %) concentrations, typical for weld deposits, influencing mechanical properties. Elements like manganese and molybdenum enhance wear resistance, while the presence of chromium (0.42 %) and nickel (0.12 %) improves corrosion resistance, crucial in aggressive environments. Keywords: large-module gears, tooth wear, electro slag surfacing, hardness, analysis
15 December 2020 in Series of Geology and Technical Sciences
The article presents the results of the study performance of cone crushers and the existing technology restoration of their parts. The main reasons for the failure of cone crushers are the following: failure armor of the cone and the middle part, the protective cap, parts of the upper suspension, dust seal rings, bearing rings, the eccentric of the crusher. The most time-consuming is to restore the details of the eccentric crusher. A new technology restoration worn surfaces of the eccentric part and the results of an experimental study of thermal friction treatment (TFТ) after surfacing are proposed. It is revealed that despite the high level of temperature corresponding to intensive treatment modes it is possible to achieve effective hardening. Implementation of the proposed technology allows: eliminate the undesirable effects of softening due to re-riveting and reduce the oxidized layer; increase productivity relative to mechanical cutting methods in 23 times and tool life of more than 10 times; the use of affordable cheap material steel 45, 50, 60G for the manufacture of tools and perform processing at more intensive modes S =0,2-1mm / Rev; n=2000-3000 rpm. It is established that the TFO of the deposited surface part eccentric, provides wear resistance of the treated surfaces parts in 2….8 times more than the factory processing technology, while the depth of the hardened layer can be 1.5…. 2 mm.