Yu Huang

Yu Huang

Auto-generated profile, based on publicly available information

Yu Huang

Department of Obstetrics and Gynecology, Sichuan Provincial People's Hospital, University of Electronic Science and Technology of China, Chengdu, China

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2022 in Annals of Translational Medicine
Verified
Journal Article
Open access
PDF file
FLFangyuan Luo
Fangyuan Luo
JYJun Yue
Jun Yue
LLLingling Li
Lingling Li
JMJie Mei
Jie Mei
XLXinghui Liu
Xinghui Liu
YHYu Huang
Yu Huang
Review Article Narrative review of the relationship between the maternal-fetal interface immune tolerance and the onset of preeclampsia Fangyuan Luo, Jun Yue, Lingling Li, Jie Mei, Xinghui Liu, Yu Huang

7 April 2021 in IEEE Journal of Photovoltaics
Verified
Journal Article
Closed access
YHYu Huang
Yu Huang
DZDayong Zhang
Dayong Zhang
MWMengge Wu
Mengge Wu
GYGenjie Yang
Genjie Yang
ZWZijun Wamg
Zijun Wamg
JYJunsheng Yu
Junsheng Yu
Perovskite solar cells (PSCs) have attracted a lot of attention due to high efficiency and low-cost fabrication processing. For planar structure PSCs, the electron transport layer (ETL) plays an important role to enhance the electron extraction capacity, device stability and balance the energy level between perovskite materials and metal electrode, which can effectively optimize the performance of PSCs. However, traditional ETL materials are not comfortable for commercialization of PSCs due to their inherent characteristics like strong aggregate, relatively low electrical conductivity, and poor ohmic contact with the metal electrodes. Here, a mixed heterojunction layer (MHL) combined an amphiphilic polymer material of poly[(9, 9-bis(3'-(N, N-dimethylamino)propyl)-2, 7-fluo-rene)-alt-2, 7-(9, 9-dioctylfluorene)] with conventional ETL materials [6, 6] phenyl C61-butyric acid methyl ester (PC 61 BM) was developed to optimize the interface characteristics between perovskite and metal electrode. Atomic force microscopy, the space charge limited current, photoluminescence measurements, and impedance spectroscopy have been measured to reveal the interface contact, electronic, and optical properties of the MHL modified PSCs device. As a result, the power conversion efficiency (PCE) of PSCs with MHL has dramatically increased from 15.17% to 18.39%. More importantly, the stability of the MHL based PSCs was improved significantly, with reduced PCE degradation (from 29% to 18%) after 160 h under ambient conditions. This research provides a simple but effective method to improve the efficiency and stability of PSCs.

22 November 2021 in Key Engineering Materials
Verified
Journal Article
Closed access
PDF file
YYYou Yang
You Yang
HLHong Shuai Li
Hong Shuai Li
YHYu Xin Huang
Yu Xin Huang
The effects of different cold rolling deformations on the microstructure and mechanical properties of high nitrogen and low nickel alloys were investigated. The microstructure of high nitrogen alloys with different rolling deformations were characterized by EBSD and TEM. The tensile mechanical properties of the high nitrogen alloys at room temperature were tested. The results showed that the microstructure of the cold rolled high nitrogen alloy with deformation of 0% to 70% shows a twinning process. The twin thickness of the high nitrogen alloy without deformation is micron degree. When the rolling deformation is over 50%, the average thickness of the deformation twin is 23nm. When the rolling deformation increases to 70%, the average thickness of the twin is 14nm. When the rolling deformation increases from 0% to 70%, the cold rolled high nitrogen alloy exhibits high strength (1001-2236 MPa) and excellent plasticity (5.9%-64.1%). It is beneficial to have a good combination of strength and plasticity after rolling deformation.