Kento Suzuki

Kento Suzuki

Auto-generated profile, based on publicly available information

Kento Suzuki

Tohoku University

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2021 in Review of Scientific Instruments
Verified
Journal Article
Open access
PDF file
KSKento Suzuki
Kento Suzuki
AKAtsushi Komuro
Atsushi Komuro
SSShintaro Sato
Shintaro Sato
MSMahoro Sakurai
Mahoro Sakurai
KMKodai Mitsuhashi
Kodai Mitsuhashi
AAAkira Ando
Akira Ando
A dielectric-barrier discharge plasma actuator (DBDPA) is a promising flow control device that can prevent flow separation around an airfoil using electrical discharges. Miniaturizing the DBDPA power supply remains a crucial technological challenge because its size and weight determine the performance of fluid devices equipped with this type of actuator. In this study, we propose a compact high-voltage AC power supply for a DBDPA intended for installation on small airplanes, including unmanned aerial vehicles. The power supply, which consists of a power supply board, a main control board, and a DC/AC converter board, is ∼110 g in weight. It can drive a 300-mm long DBDPA without any substantial voltage drop. The power consumption in standby remains below 1 W, and the maximum consumption during discharge in burst mode at a burst ratio of 5% is 24 W. The power supply uses a lithium-ion battery with a capacity of 1800 mA h, which allows continuous DBDPA operation for ∼1.5 h. An experiment was conducted in a wind tunnel using an airfoil model whose cross-section corresponds to that of an airfoil from a commercial glider airplane. Experimental results reveal that the surface pressure around the airfoil is modified by DBDPA operation, clearly demonstrating the effectiveness of the developed power supply for operating a DBDPA as a flow control device. The size and weight of the proposed power supply can be established as a benchmark to further miniaturize and optimize DBDPA power supplies.

1 January 2025 in Review of Scientific Instruments
Verified
Journal Article
Closed access
AKAtsushi Komuro
Atsushi Komuro
KSKento Suzuki
Kento Suzuki
Katsuyuki TakahashiKatsuyuki Takahashi
Katsuyuki Takahashi
HSHiroshi Sato
Hiroshi Sato
TKTakeharu Kuroiwa
Takeharu Kuroiwa
KSKunihiro Sakamoto
Kunihiro Sakamoto
In this study, we present the development of a compact and lightweight nanosecond pulsed power supply designed to improve the performance of plasma actuators for flow control on unmanned aerial vehicles (UAVs). While traditional AC power supplies are commonly used in plasma actuators, the nanosecond pulsed power supplies offer the advantage of operating over a wider range of Reynolds numbers, making them highly desirable. However, miniaturization and weight reduction of pulsed power supplies pose significant challenges. To address these issues, we present a novel approach using a high-voltage silicon carbide (SiC) MOSFET to create an inductive energy storage (IEC) power supply, eliminating the need for a bulky transformer core. This innovation results in a more compact and lightweight pulsed power supply, potentially improving aerodynamic control in UAV applications. The size and weight of the power supply developed is comparable to the smallest AC power supplies developed to date. In addition to basic current–voltage measurements, the performance of the power supply for airflow control is evaluated through wind tunnel experiments. As a result, the plasma actuator powered by the developed nanosecond pulsed power supply shows superior performance compared to previous studies, despite its small size and light weight.

1 January 2019 in The Proceedings of Mechanical Engineering Congress, Japan
Verified
Journal Article
Closed access
PDF file
MTMotofumi Tanaka
Motofumi Tanaka
NKNoritsugu Kubo
Noritsugu Kubo
HKHirokazu Kawabata
Hirokazu Kawabata
KSKento Suzuki
Kento Suzuki
SBSagar Bhandari
Sagar Bhandari
YOYukihiro Oryu
Yukihiro Oryu

30 November 2020 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
KSKento Suzuki
Kento Suzuki
MAMasayui Arai
Masayui Arai
KIKiyohiro Ito
Kiyohiro Ito
MFMakoto Fujioka
Makoto Fujioka
THTomohide Harada
Tomohide Harada
TITatsuya Inoue
Tatsuya Inoue
Thermal barrier coating (TBC) is applied to gas turbine blades to protect the metallic substrate from high- temperature gas flow. TBC consists of the following double layers: top coating (TC) with high thermal insulation and bond coating (BC) with high oxidation resistance. To ensure the long-term reliability of TBC, it is necessary to characterize the thermal insulation and adhesion strength of TBC by using a simple method. In this study, an indentation test involving a Rockwell indenter was applied. The indenter was used on the surface of the TBC specimens prepared under different spray conditions to obtain an indentation curve. Subsequently, the relationship between the parameters based on the indentation curve and the coating properties of TBC, such as porosity, thermal conductivity, Young’s modulus, and interfacial fracture toughness, was investigated. The results indicated that the coating properties of TBC can be characterized by the non-dimensional indentation depth, defined as hr/hmax, and the slope of the loading curve denoted as k1 in the parameters.

1 January 2019 in The Proceedings of Mechanical Engineering Congress, Japan
Verified
Journal Article
Closed access
PDF file
KNKoki Nankai
Koki Nankai
KSKento Suzuki
Kento Suzuki
AKAtsushi Komuro
Atsushi Komuro
TNTaku Nonomura
Taku Nonomura
KAKeisuke Asai
Keisuke Asai
A linear reduced-order model of flow fields around an airfoil controlled by a plasma actuator is constructed based on experimental data. An alternating-current dielectric-barrier-discharge plasma actuator (ac-DBDPA) with random input was used to control flow fields around a NACA0015 airfoil at the chord Reynolds number of 6.4 × 104 in a wind tunnel testing and time-resolved data of the velocity fields were obtained by particle image velocimetry. Proper orthogonal decomposition (POD) was employed to the data and the lower-dimensional description of them was obtained by using the first ten POD modes. Subsequently, the least-squares method was applied to the time history of the POD modes and the control input corresponding to the voltage amplitude of ac-DBDPA, and the coefficient matrix of the linear model was computed. The effects of the control input on the velocity fields reconstructed by the POD modes were investigated from the input matrix. It is shown that the velocity fields are not influenced much when the average value of the input is changed. On the other hand, they are sensitive to the input change. This result corresponds to the fact that the intermittent actuation is effective for the flow control by plasma actuators such as the burst-mode actuation or nanosecond-pulse-driven DBDPA.