2 October 2019 in Optics Express
Source-free all optical sampling, based on the convolution of the signal spectrum with a frequency comb in an electronic-photonic, co-integrated silicon device will be presented for the first time, to the best of our knowledge. The method has the potential to achieve very high precision, requires only low power and can be fully tunable in the electrical domain. Sampling rates of three and four times the RF bandwidths of the photonics and electronics can be achieved. Thus, the presented method might lead to low-footprint, fully-integrated, precise, electrically tunable, photonic ADCs with very high-analog bandwidths for the digital infrastructure of tomorrow.
11 March 2019 in IEEE Journal of Selected Topics in Quantum Electronics
Dense wavelength division multiplexers are key components of data communication networks. This work presents a silicon-photonic eight-channel multiplexer device with a channel spacing of only 0.133 nm (17 GHz). Devices were fabricated in a commercial silicon foundry, in 8" silicon-on-insulator wafers. The device layout consists of seven unbalanced Mach-Zehnder interferometers in a cascaded tree topology, and each interferometer unit also includes a nested ring resonator element. The transfer function of each unit is that of a maximally-flat, auto-regressive, moving-average filter. The devices are characterized by uniform passbands, sharp spectral transitions between pass and stop bands, and strong out-of-band rejection. The worst-case optical power crosstalk is -22 dB. The proper function of the device requires careful control of optical phase delays over 14 distinct optical paths. Post-fabrication trimming of phase delays was performed through local illumination of a photo-sensitive upper cladding layer of chalcogenide glass. The de-multiplexing of three adjacent QAM-16, 40 Gbit/s wavelength-division channels was successfully demonstrated. The devices are applicable in data communication and in integrated-photonic processing of radio-over-fiber waveforms.
1 February 2022 in Journal of Lightwave Technology
A dynamic photonic instantaneous microwave frequency measurement approach is reported based on frequency-to-time mapping and filtering using an integrated ring resonator, a local oscillator for heterodyne detection, and an electrical bandpass filter. The unknown signal is time-swept through the narrow linewidth of the ring resonator, realized on a silicon nitride platform. A shifted local oscillator at a fixed frequency difference from the center of the ring resonator defines an intermediate frequency for heterodyne detection. After conversion to the electrical domain using a photodiode, this intermediate frequency is filtered by a narrowband electrical bandpass filter. The proposed system demonstrates a resolution of less than 1 MHz and a measurement accuracy of $\pm$ 0.4 MHz over a frequency range of 10 GHz, only limited by the used experimental components. To the best of our knowledge, this is the highest accuracy and resolution shown so far for photonic microwave frequency measurement systems. Since the method can be easily integrated on any photonic platform, it might become an integral part of future wireless devices.
8 February 2022 in IEEE Photonics Journal
The growing demand for bandwidth and energy efficiency requires new solutions for signal detection and processing. We demonstrate a concept for high-bandwidth signal detection with low-speed photodetectors and electronics. The method is based on the parallel optical sampling of a high-bandwidth signal with sinc-pulse sequences provided by a Mach-Zehnder modulator. For the electronic detection and processing this parallel sampling enables to divide the high-bandwidth optical signal with the bandwidth $B$ into $N$ electrical signals with the baseband bandwidth of $B/(\text{2}\,N)$ . In proof-of-concept experiments with $N=3$ , we present the detection of 24 GHz optical signals by detectors with a bandwidth of only 4 GHz. For ideal components, the sampling and bandwidth down-conversion does not add an excess error to the signals and even for the non-ideal components of our proof-of-concept setup, it is below 1%. Thus, the rms error for the measurement of the 24 GHz signal was reduced by a factor of about 3.4 and the effective number of bits were increased by 1.8.
28 April 2021 in Optics Express
Increasing demands for data centers, backbone, access, and wireless networks require inventive concepts to transmit and distribute digital or analog signal waveforms. We present a new, extremely simple transceiver concept, fundamentally different from conventional approaches. It does not rely on high-speed electronics and enables transmission of various time multiplexed analog waveforms or digital data signals with the maximum possible symbol rate in the same rectangular optical spectral band B. The aggregate symbol rate of N signal channels corresponds to B or twice the used modulator’s electro-optical bandwidth. By a modification of the system, it can be increased to three times the modulator bandwidth. The rectangular spectra can be further multiplexed into wavelength-superchannels without guardbands. To time demultiplex single signal channel, just another intensity modulator and a detector with an electrical bandwidth corresponding to the channel’s baseband width (B/(2N)) is required. No optical filter, high-speed signal processing, or unconventional photonic devices are needed; thus, it has the potential to be easily integrated into any platform and provides an economical and energy-efficient solution for future communication networks and microwave photonic links.
20 November 2020 in IEEE Photonics Technology Letters
A new method for high-speed photonic arbitrary waveform generation using optical sinc-pulse sequences and Mach-Zehnder modulators is presented, enabling a three-to four-fold increase in sampling rate compared to the bandwidth of the used modulator for generating the pulses and an N-fold increase compared to the bandwidth of the incorporated electronics, with N as the number of parallel branches. Proof of concept experimental results, using conventional off-the-shelf fiber components have been presented in this study. Due to its simplicity and the possibility to achieve high sampling rates with low bandwidth photonic and electronic equipment, this method is beneficial for integration on a silicon photonics platform.