The focus of this work is on the nature of self-healing of ionically modified rubbers obtained by reaction of brominated poly(isobutylene-co-isoprene) rubber (BIIR) with various alkylimidazoles such as 1-methylimidazole, 1-butylimidazole, 1-hexylimidazole, 1-nonylimidazole, and 1-(6-chlorohexyl)-1H-imidazole. Based on stress–strain and temperature dependent DMA measurements, a structural influence of the introduced ionic imidazolium moieties on the formation of ionic clusters and, as a consequence, on the mechanical strength and self-healing behavior of the samples could be evidenced. These results are fully supported by a molecular-level assessment of the network structure (cross-link and constraint density) and the dynamics of the ionic clusters using an advanced proton low-field NMR technique. The results show distinct correlations between the macroscopic behavior and molecular chain dynamics of the modified rubbers. In particular, it is shown that the optimization of material properties with regard to mechanical and self-healing behavior is limited by opposing tendencies. Samples with reduced chain dynamics exhibit superior mechanical behavior but lack on self-healing behavior. In spite of these limitations, the overall performance of some of our samples including self-healing behavior exceeds distinctly that of other self-healing rubbers described in the literature so far.
27 February 2018 in ACS Sustainable Chemistry & Engineering
In this study we describe the synthesis of bis(pyrrolidone) based dicarboxylic acids from itaconic acid and their application in 2-oxazoline resins for fully renewable thermoset materials. The monomers are obtained using a bulk aza-Michael addition of a diamine and two itaconic acid molecules using a catalytic amount of water. The monomers can be isolated in high purity after recrystallization, though their yield proved highly dependent on the selected diamine spacer length: In general, only the dicarboxylic acids containing diamines with an even number of methylene spacers are isolated in high yields. Through NMR, GPC, and FTIR analysis we demonstrate that these bis(pyrrolidone) based dicarboxylic acids exhibit significantly enhanced curing rates in 2-oxazoline resins compared to resins containing aliphatic dicarboxylic acids such as sebacic acid. Overall we demonstrate that the rate of 2-oxazoline ring opening addition with carboxylic acid functionalities is determined by the used dicarboxylic acid, whereas the ring opening addition of the 2-oxazoline functionality with amide groups is determined by the used bis(2-oxazoline) compound. The thermosets obtained after curing proved to be readily plasticized by water, opening up possibilities for enzymatic degradation.
We report on the role of temperature and shear on the melt behavior of iPP in the presence of the organic compound N1,N1′-(propane-1,3-diyl)bis(N2-hexyloxalamide) (OXA3,6). It is demonstrated that OXA3,6 facilitates a viscosity suppression when it resides in the molten state. The viscosity suppression is attributed to the interaction of iPP chains/subchains with molten OXA3,6 nanoclusters. The exact molecular mechanism has not been identified; nevertheless, a tentative explanation is proposed. The observed viscosity suppression appears similar to that encountered in polymer melts filled with solid nanoparticles, with the difference that the OXA3,6 compound reported in this study facilitates the viscosity suppression in the molten state. Upon cooling, as crystal growth of OXA3,6 progresses, the decrease in viscosity is suppressed. Retrospectively, segmental absorption of iPP chains on the surface of micrometer-sized OXA3,6 crystallites favors the formation of dangling arms, yielding OXA3,6 crystallites decorated with partially absorbed iPP chains. In other words, the resulting OXA3,6 particle morphology resembles that of a hairy particle or a starlike polymer chain. Such hairy particles effectively facilitate a viscosity enhancement, similar to branched polymer chains. This hypothesis and its implications for the shear behavior of iPP are discussed and supported using plate–plate rheometry and slit-flow experiments combined with small-angle X-ray scattering analysis.
17 April 2019 in ACS Sustainable Chemistry & Engineering
In this study, we report on the synthesis and characterization of thermosets based on the renewable N,N’-octamethylene-bis(pyrrolidone-4-carboxylic acid) (BP-C8) and 1,3-bis(4,5-dihydro-2-oxazolyl)benzene (IAox). The BP-C8, having two pyrrolidone rings, is obtained via a bulk aza-Michael addition reaction of 1,8-diaminooctane with two equivalents of itaconic acid using water as catalyst. Thermosets are prepared by mixing the desired ratio of BP-C8 with IAox, followed by thermal curing at 180 °C. The cross-link density of the thermosets is controlled by the usage of an excess of bis(2-oxazoline) and the achievement of full conversion is confirmed by Fourier Transform infrared spectroscopy. As anticipated, the glass transition temperature of the thermosets increases with increasing cross-linking density to values up to 100 °C. All thermosets are found to absorb water upon storage, resulting in a strong plasticizing effect and thus a suppression of the glass transition temperature. To assess the role of water on the thermo-mechanical properties, all thermosets are exposed to various relative humidity and their mechanical performance is evaluated. In general, we observe that the suppression in Tg under the influence of water facilitates a brittle-to-ductile transition as the Tg of the thermosets approach room temperature. Additionally, in this study we demonstrate that the hydrolysis of the ester bonds in the thermosets can be enforced at elevated temperatures in the presence of water, resulting in the liberation and migration of BP-C8 monomer. Interestingly, BP-C8 can readily be isolated by filtration as is crystallizes from water during cooling, thereby providing a promising route for its chemical recycling. Overall, these findings indicate that water plays a pivotal role in these poly(ester-amide)s as it functions as a catalyst in the BP-C8 synthesis, governs the thermal and mechanical properties of the thermosets, and opens up routes for chemical recycling of BP-C8 after hydrolysis as it acts as a recrystallization (co-)solvent.
A covalent adaptable network reinforced with microfibrillated cellulose is found to be an attractive intermediate between a thermoset and thermoplastic material.