18 July 2022 in Advances in Materials Science and Engineering
Cutting force is one of the significant parameters in the metal cutting process. The metal cutting process is the primary in the production and manufacturing industry to produce high-quality products. Every production and manufacturing needs to develop a technology, i.e., a cooling or lubrication system at the cutting zone while doing the metal cutting process. This current work focuses on developing the machine learning algorithm by using three different types of regression processes, namely, polynomial regression process (PR), support vector regression (SVR), and gaussian process regression (GPR). These three processes are developed to predict the machine learning force, cutting power, and cutting pressure by controlling primary factors (cutting speed, depth of cut, and feed rate). The cooling or lubrication process also affects the machining process. We need to maintain the minimum qualifications to perform under minimum quality lubrication (MQL) and high-pressure coolant (HPC). The ANN algorithm was used to run different parameters, and these parameters are optimized for cutting force.
12 March 2024 in Advances in Tribology
PCPedro Dionisio Remedios Castañeiras
Pedro Dionisio Remedios Castañeiras
Automobile engines require lubrication to lessen the impact of friction due to the high levels of wear and frictional heat generated by the sliding parts. Wear and friction will cause engine parts to endure for less time, be less reliable, and require more maintenance. Diesel fuel can potentially be replaced with biodiesel among other fuels. Diesel engines have a serious problem with equipment that is lubricated by the fuel itself. This studys goal is to assess the influence of bio-additives on the diesel fuel tribological behavior and energy balance during the cars idle running, acceleration, constant speed, and braking. Lubricity issues with reformulated diesel and lubricity test procedures are explained. The relationship between tribology and bio-additives is also briefly illustrated. According to the literature, adding bio-additives to fuel boosts its lubricity. Biodiesel has long been considered an additive with excellent lubricant properties. Even in small amounts, adding biodiesel to diesel fuel can increase its lubricity without the need for conventional lubricity additives. This is especially true for diesel fuel with ultralow sulfur. Diesel fuel characteristics determine the precise blending percentage needed to provide the proper lubricity of maximum 520μm testing wear scars with a high-frequency reciprocating rig (HFRR), although 2 biodiesel nearly invariably imparts adequate lubricity to biodiesel blends. Tall oil fatty acid (TOFA) was one of the bio-additives investigated by HFRR. When the additive concentration was raised from 0 to 500g/g, the wear scar diameter (WSD) of nonadditive diesel fuel was lowered by 60.3, from 630 to 250μm, and the coefficient of friction (COF) was lowered by 95.7, from 0.47 to 0.02.
14 October 2021 in Journal of Nanomaterials
This research investigates the tribological behavior of gray cast iron against EN31 steel under lubricated conditions. The most typical lubricated sliding phenomena are the reduction of wear on both the sliding surfaces and any one of the critical surfaces. Static and hydrodynamic wear can be reduced based on fluid properties or the accessibility of fluid between the surfaces. The oil’s viscosity or content of the hydrocarbon and additives present in the oil plays a major role in controlling the wear of reciprocating surfaces. Therefore, this research work focused on metal-to-metal contact wear under the influence of lubricating oil (40 pride oil). The Taguchi method was used to select the sliding parameter combinations. Lubricated sliding resulted in a relatively reduced order of friction coefficient, attributable to better load distribution due to the formation of the lubricant film.
13 August 2021 in Journal of Nanomaterials
This present work focused on investigating the thermal behavior and emission level of sapodilla oil mixed with diesel to an internal combustion (IC) engine. The behavior of the engine is measured via brake thermal efficiency (BTE), brake-specific energy consumption (BSEC), heat release rate (HRR), cylinder pressure, and cumulative heat release rate (CHRR). The test results were evaluated with diesel fuel. Carbon deposits were low in sapodilla seed oil with slight variation of calorific value than standard diesel fuel. BTE value for case B20 is found to equal diesel fuel. For lower and higher blends, the cylinder pressures are lower than the diesel fuel. HRR decreased as increased of the blend ratio. Inferior blends of sapodilla are emitted lower HC and CO. The BTE of B100 works 88.13 efficiently, similar to diesel for low load conditions. When compared to diesel, a maximum NOx reduction of up to 30 was achieved while using the sapodilla blend. It is found that the oil derived from the sapodilla seed kernels will be the promising additive for fossil fuels for a greener environment.