Alex Molina

Alex Molina

Auto-generated profile, based on publicly available information

Alex Molina

Department of Materials Science and Engineering, The Pennsylvania State University, University Park, USA

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 September 2021 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
SHSang-Woo Han
Sang-Woo Han
JSJianan Song
Jianan Song
MSMansura Sadek
Mansura Sadek
AMAlex Molina
Alex Molina
MEMona A. Ebrish
Mona A. Ebrish
RCRongming Chu
Rongming Chu
This article reports GaN super-heterojunction Schottky barrier diodes (SHJ-SBDs) with substantially improved performance. Metal-2DEG sidewall n-ohmic contacts were deployed to achieve low contact resistance of $0.75~\Omega ~ \cdot ~mm$ , avoiding the risk of abnormally high contact resistance caused by inaccurate etch depth control. A pGaN notch formed near the cathode successfully eliminated excessive hole conduction caused by the sidewall n-ohmic contact. Isolation was improved by a high-energy Al implantation step. The resulting SHJ-SBD exhibited a breakdown voltage (BV) of ~12.5 kV and a specific resistance of 100.8 $\text{m}\Omega ~ \cdot ~cm^{2}$ .

18 April 2018 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
HSHamed Simchi
Hamed Simchi
KCKayla A. Cooley
Kayla A. Cooley
ZDZelong Ding
Zelong Ding
AMAlex Molina
Alex Molina
SMSuzanne E. Mohney
Suzanne E. Mohney

6 September 2021 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
AMAlex Molina
Alex Molina
ICIan E. Campbell
Ian E. Campbell
TWTimothy N. Walter
Timothy N. Walter
AAAma D. Agyapong
Ama D. Agyapong
SMSuzanne E. Mohney
Suzanne E. Mohney
Molybdenum carbonitride films prepared by plasma enhanced atomic layer deposition were studied for use as Schottky contacts to n-type gallium nitride. Deposited using bis(tertbutylimino)bis(dimethylamino)molybdenum and a remote plasma N2/H2 plasma, the diodes capped with Ti/Au displayed excellent rectifying behavior with a barrier height of 0.87 ± 0.01 eV and an ideality factor of 1.02 ± 0.01 after annealing at 600 °C in N2. These characteristics surpass those of pure metal nitride Schottky diodes, possibly due to work function engineering due to the incorporation of C and use of a remote plasma to avoid process-induced defects. According to x-ray photoelectron spectroscopy and energy-dispersive x-ray spectroscopy, the film composition is approximately MoC0.3N0.7. Grazing incidence x-ray diffraction and plan-view transmission electron microscopy selected area electron diffraction are consistent with a rock salt structure with a lattice parameter of 0.42 nm.

18 May 2022 in Materials Science in Semiconductor Processing
Verified
Journal Article
Closed access
AMAlex Molina
Alex Molina
SMSuzanne E. Mohney
Suzanne E. Mohney

12 February 2020 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Open access
PDF file
AMAlex Molina
Alex Molina
JSJeffrey R. Shallenberger
Jeffrey R. Shallenberger
SMSuzanne E. Mohney
Suzanne E. Mohney
Hydrobromic acid (HBr) vapor was used to remove native oxide from an undoped (100) germanium (Ge) wafer with n-type conductivity and to passivate its surface against reoxidation. The Ge surfaces, examined by x-ray photoelectron spectroscopy, were suspended above a 48% HBr solution for 1, 10, 20, 60 min, and 24 h. A steady decrease in oxide thickness was observed for up to 60 min of HBr exposure time. Beyond this time, little or no difference was observed, and the wafers maintained subnanometer levels of oxidation. The stability of the passivated surface was then measured with each treated sample exposed to ambient air for 19 h. The samples exposed to HBr for 60 min or less reoxidized when exposed to air, while the sample previously exposed to HBr for 24 h showed levels of oxidation similar to the freshly passivated wafer, thereby demonstrating HBr vapor-phase treatment as a simple method for passivating Ge.

30 May 2021 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
AMAlex Molina
Alex Molina
SDSteven P. Dail
Steven P. Dail
ICIan E. Campbell
Ian E. Campbell
TWTimothy N. Walter
Timothy N. Walter
MTMichael W. Thomas
Michael W. Thomas
SMSuzanne E. Mohney
Suzanne E. Mohney
Although silicon (Si) currently dominates the semiconductor industry, its small 1.1 eV band gap limits its maximum operating temperature, which restricts its use in high-temperature, high-power devices. Gallium nitride (GaN) is an attractive semiconductor with its wide bandgap (3.4 eV), high electron mobility (1700 cm2/Vs), high electron saturation velocity (3 x 107 cm/s), large critical breakdown field (2 MV/cm), and thermal stability. The high-power capabilities of GaN allow for a reduction in device size, which can conserve physical space if used to replace conventional Si power devices. While the semiconductor itself can endure harsh operating conditions, the reliability of the metal/semiconductor contacts can be a limiting factor for its use. Schottky contacts should provide a high barrier height and low reverse leakage current, and they must be electrically stable over the lifetime of the device. In this study, three materials reported to have high work functions are compared as Schottky diodes to n-type GaN, each selected for its anticipated thermodynamic stability with GaN1 or the potential to minimize process-induced defects in the diodes or both. Rhenium (Re) diodes fabricated via electron beam deposition, molybdenum nitride (MoNx) diodes via remote plasma atomic layer deposition (ALD), and palladium (Pd) diodes via electroless deposition were investigated. Ti/Al-based ohmic contacts were employed. The Re/n-GaN Schottky diode was chosen for study because of its thermodynamic stability against metallurgical reactions1 and high work function (4.96 eV)2. The barrier heights were investigated by current–voltage (I-V) and capacitance–voltage (C-V) measurements at room temperature. Both techniques demonstrated that the barrier height increased after an anneal at 400°C for 5 min, yielding a barrier height of 0.88 eV and ideality factor of 1.02 from by I-V measurements, while the C-V measurements revealed a barrier height of 0.91 eV. These barrier heights and reverse leakage currents remained stable upon annealing in N2 at 600°C. The MoNx/n-GaN Schottky diode was chosen for study because of the reported high work function of MoNx (5.33 eV)3, its conductive and refractory nature, and its thermodynamic equilibrium with GaN4. Films were deposited with bis (tert-butylimido)-bis (dimethylamido) molybdenum and a 300 W remote N2/H2 plasma. Four-point probe measurements and x-ray photoelectron spectroscopy (XPS) were used to measure sheet resistance and composition. Barrier heights from the I-V measurements were 0.41 eV, and ideality factors were 1.4, with good stability upon annealing at 600°C. The Pd/n-GaN Schottky diode was chosen because of its high work function (5.12 eV)2 and its potential to be electrolessly deposited, offering a gentle technique to minimize process-induced defects in the GaN, although Pd is not expected to be in thermodynamic equilibrium with GaN. A new method for electroless deposition of Pd films onto GaN surfaces used palladium dichloride with sodium L-ascorbate as the reducing agent was developed. Profilometry, four-point probe measurements, energy dispersive x-ray spectroscopy, and XPS were used to measure film thickness, sheet resistance, resistivity, morphology, and composition. The process provided conductive and pure Pd films, but some challenges with nucleation of the film on GaN makes the process less robust. Barrier heights from the I-V measurements were 1.13–1.26 eV, and ideality factors were 1.02–1.05. However, Pd is not in thermodynamic equilibrium with GaN. Among the candidates tested so far, the Re diodes were overall the strongest candidate. Future work will involve stress testing followed by materials characterization to provide more information on stable metallizations for high-power GaN devices. The authors are grateful to Sandia National Laboratories (Andrew Allerman) for providing GaN epilayers. This work was funded by the Office of Naval Research under Grant N000141812360, distribution A, approved for public release, distribution is unlimited (DCN# 43-7434-20). S. E. Mohney and X. Lin, J. Electron. Mater, 25, 811–818 (1996). H. Michaelson, J. Appl. Phys. 48, 4729-4733, (1977): H. Matsuhashi and S. Nishikawa, Jpn. J. Appl. Phys., 33, 1293, (1994). H. S. Venugopalan and S. E. Mohney, Z Metallkd., 89, 184-186, (1998).