The accumulation of petroleum polymers compromises biodiversity and causes environmental problems. Nanocellulose enhances biodegradability and can improve the physical-mechanical performance of materials. The objective was to produce and characterize hybrid films composed of bacterial cellulose (BC) and plant nanocellulose from Eucalyptus (Euc) or Pinus (Pin). Films were produced by the casting method using filmogenic suspensions with different cellulose nanofibrils (CNFs) proportions from both the sources (0, 25, 50, 75 and 100 %). CNFs suspensions were characterized by transmission electron microscopy. The morphology of the films was analyzed using scanning electron microscopy. In addition, the transparency, contact angle, wettability, oil and water vapor barrier and mechanical properties were also evaluated. The contact angles were smaller for films with BC and the wettability was greater when comparing BC with plant CNFs (0.10 ° s − 1 {\text{s}^{-1}} for 75 % Euc/25 % BC and 0.20 ° s − 1 {\text{s}^{-1}} for 25 % Euc/75 % BC). The water vapor permeability (WVP) of the 100 % BC films and the 25 % Euc/75 % BC composition were the highest among the studied compositions. Tensile strength, Young’s modulus and puncture strength decreased considerably with the addition of BC in the films. More studies regarding pre-treatments to purify BC are needed to improve the mechanical properties of the films.
This work brings the first detailed characterization of Patauá mesocarp fibers. Short thick-walled fiber cells compose flat bundles covering the patauá seeds . Alkali treatments removed amorphous components and raised cellulose up to 50%. Mercerization enhanced fiber morphology and density for composite applications.
Background: Converting açaí waste fibers into kraft pulp and paper demands high amounts of preserved fibers. Manual removal preserves the fibers, but mechanical methods are faster. Therefore, this work aimed to compare three methods to extract açaí fibers from the seed’s surface concerning efficiency and fiber quality for cellulose pulping. Results: Açaí waste fibers have ≈ 34 % of cellulose and ≈ 61% of non-cellulose structural components (based on extractive free mass) and ≈ 6% of non-structural extractives and ashes (based on total mass). They occur united into bundles that dissociate into short (388 µm) fiber cells. Their pulp-paper quality indexes were aspect ratio (31.8-41.2), wall fraction (52.8 %), flexibility coefficient (47.2 %), boiler index (0.6), Runkel index (1.2), and Mulsteph index (0.8). The manual removal preserved the fibers but had the lowest efficiency (0.1 g/min). The food processor provided intermediate preservation of the fibers and efficiency (0.5 g/min). Despite the highest efficiency (3.9 g/min) of the hammer mill method, the friction with the hammers damaged the fibers and increased the levels of extractives from 4 to 8% and hemicelluloses from 34 to 40%. Conclusion: Açaí waste fiber bundles are dissociable into short fibers and have a favorable chemistry for kraft pulping and developing cellulose products. The fiber morphology is not ideal, but not limiting, demanding adjustments in the future kraft pulping parameters. The extraction of the fiber by the food processor is recommended, which is manageable to the local communities to support an integrated bioeconomy of the açaí waste.
2 September 2024 in Research, Society and Development
O intuito inicial deste trabalho foi estudar a tensão superficial e a viscosidade de óleos e de misturas de óleos visando desenvolver um estudo sobre a miscibilidade desses lubrificantes. Ao fazer os testes descritos, pouca variação foi obtida inviabilizando tal estudo. Nessas condições, optou-se apenas por investir no que já seria a segunda etapa do trabalho: investigar a interação desses óleos e das misturas dos mesmos com uma determinada superfície metálica, visando assim, correlacionar a molhabilidade do óleo na superfície com a eficiência de lubrificação do mesmo. Para isso, foram utilizados dois óleos e três misturas dos mesmos, totalizando cinco amostras. Como resultado final, obteve-se a maior molhabilidade, numa superfície de alumínio, para a mistura 50-50, denotando, assim, que a mesma possuía maior interação com a superfície metálica e, teoricamente, uma maior eficiência de lubrificação. A eficiência citada seria maior desde que os outros componentes dessa mistura não apresentassem uma incompatibilidade muito grande. Evidentemente, a análise química demandada para sanar tal preocupação foi deixada como sugestão para trabalhos futuros.