12 March 2019 in Nuclear and Radiation Safety
The possibility of the plasma processing of low-level or intermediatelevel radioactive wastes in the reactor equipped with arc plasmatrons is shown. The reactor design for the plasma processing of the radioactive wastes that allows promoting the efficiency of the plasma processing of the radioactive wastes (RAW) by the increasing of the speed and the intensity of the plasma pyrolysis is proposed. The various methods for RAW preparation, dosage and supply into the plasmochemical reactor have been investigated. The waste which is supplied to the reactor can be in various aggregate states (solid, liquid or gaseous) depending on which different kinds of preparation, dosage, and supply of RAW materials to the plasmochemical reactor are used. The solid waste must be ground for increasing of the phase separation surface. The degree of grinding of the wastes depends on their further reprocessing. The reactor allows processing of the mixed-type radioactive waste, which includes both combustible and non-combustible components. The wastes can be packed or ground up. The selected technological regimes should provide temperature from 1500 °C in the melting chamber to 250 °C in the upper part in the pyrogas exit zone to prevent the flow-out of volatile compounds of a series of radionuclides and heavy metals from the furnace and to process the waste and merge slag melt without adding of fluxes. The fused slag is a basaltiform monolith, where the content of aluminum oxide reaches 28%; silicon oxide up to 56%; sodium oxide from 2.5 to 11 %. The resulting radioactive slag is extremely resistant to the chemical influence. The pyrogas produced in the shaft furnace will have a heating value of about 5 MJ/nm3. This allows, after initial heating by plasmatron, maintaining the required temperature in the combustion chamber due to the heat released during combustion of the pyrogas, when the plasma heating source is switched off, and burning the resin and soot effectively. It is proved that the plasma technology for RAW reprocessing allows a significant reduction in waste volumes and waste placement for long-term storage with the most efficient use of storage facilities.
23 June 2022 in Military Technical Collection
У роботі, використовуючи метод математичного моделювання, а також закони термодинаміки, одержано аналітичні залежності для дослідження напружено-деформованого стану сферичних резервуарів в залежності від різних температур поверхні цієї конструкції. Проведені розрахунки показали, що радіальні напруження є незначними у порівнянні з тангенціальними, які діють на розтяг. Найбільше абсолютне значення тангенціальні напруження приймають на внутрішній поверхні сферичної конструкції, які діють на розтяг та на зовнішній – стиск. Результати досліджень представлені графічно.
28 February 2019 in Scientific Bulletin of UNFU
Розроблено метод розрахунку процесу газифікації низькосортного палива, який дає змогу провести розрахунок параметрів робочого процесу в газифікаторі зі суцільним шаром, який є найбільш технологічно та конструктивно простим. Проаналізовано фізичні моделі процесу газифікації твердого палива, які дають змогу побудувати методику розрахунку параметрів робочого процесу у газифікаторі, засновану на рівняннях теплового і матеріального балансів, вигорання і газифікації вуглецю, що сприяє підвищенню екологічних показників та модернізації наявних інженерних методів розрахунку. Використано стандартизовані методи проведення досліджень процесу газифікації низькосортного палива. У процесі розроблення газогенераторної установки, що дає змогу виробляти синтез-газ, застосовано сучасні методи використання відповідних контрольно-вимірювальних пристроїв. Використано математичне планування експериментальних досліджень. Розроблено метод розрахунку процесу газифікації деревини, який дає змогу провести розрахунок параметрів робочого процесу в газифікаторі зі суцільним шаром, засновану на рівняннях теплового і матеріального балансів. На основі експериментальних досліджень складено матеріальний і тепловий баланси процесу газифікації деревини породи сосна (Pinus sylvestris). Показано, що під час газифікації соснової деревини невеликі втрати тепла виходять внаслідок винесення пилу і втрат вуглецю із золою і шлаком.
23 December 2025 in Eastern-European Journal of Enterprise Technologies
This study examines the heat exchange processes for thermally active and thermally sensitive individual nodes and elements in electronic devices that are subjected to thermal loads in the areas of canonical form. As a result of thermal loads, significant temperature gradients arise. To improve the accuracy of designing electronic devices and for their effective operation, linear and nonlinear mathematical models have been built to analyze their temperature regimes. Based on the stated linear and nonlinear axisymmetric boundary value problems of heat conduction, their analytical and analytical-numerical solutions have been derived. Using these solutions has made it possible to establish the temperature distribution in spatial radial and axial coordinates for given geometric and thermophysical parameters (the chosen graphite has the ability to absorb a significant amount of heat at its thermal conductivity coefficient equal to 372 W/(m∙degree)). To effectively describe canonical heating regions, the theory of generalized functions has been used. A technique for linearizing nonlinear mathematical models has been introduced. As a result, linear second-order differential equations with partial derivatives and a singular right-hand side have been derived. The numerical results reflect the temperature distribution in the medium along the radial and axial coordinates for the given geometric and thermophysical parameters. The number of divisions of the interval (0; r*) was chosen to be 9, which made it possible to obtain numerical values of temperature with an accuracy of 10-6. The resulting numerical values of temperature for the selected materials with a linear temperature dependence of the thermal conductivity coefficient differ from the results obtained for its constant value by 5%. The constructed mathematical models of heat transfer make it possible to analyze spatial isotropic media with respect to their thermal stability
30 November 2023 in European Science
As a result of the work, it is shown that electricity generation is a complex and dangerous process. The most fire and explosion hazardous technological process of electricity generation at power plants is the process associated with the operation of hydr