30 October 2020 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
SSSenthilkumar Subramaniam
The effect of partial shading results in increased mismatch losses and decreased power output of the solar Photovoltaic (PV) array, requiring reconfiguration of the shading pattern of the panels. Hence, various interconnection schemes and shade dispersing techniques are used to increase the power harnessed from the PV array. This paper proposes a simple offline shade dispersion in the entire PV array using a fixed reconfigured interconnection scheme. MATLAB/Simulations are carried out on a 6 × 6 PV array with fairly larger rating with different shading patterns and an experimental set up has also been developed with a 3 × 3 PV array with a much smaller rating in the laboratory for validating the reduction in mismatch loss and increased fill factor for different shading patterns. This technique can be used for both square and rectangular PV arrays. The proposed interconnection scheme has been compared with the Total Cross Tied (TCT) connection and shown that there is an enhancement of power generation, for about 16.66% in short-narrow shading pattern and a reduction in power loss of 66.66% in a short-wide pattern.
21 January 2022 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
There is a significant effect of partial shade on the generation of power from solar plants. Hence, this paper proposes a new simple reconfiguration technique called Sequential Arrangement Technique (SAT) to disperse the shade on Photo-Voltaic (PV) modules. This method facilitates the numbering of the PV modules, based on the shading pattern during the PV array installation. Furthermore, the PV modules irradiation is distributed column-wise by providing wiring similar to Total Cross Tied (TCT) connection to get minimum row current and enhanced maximum power of 12.31% compared to conventional TCT. The performance of SAT is validated through the analysis, MATLAB simulations, and experimentation under various shading patterns. Furthermore, the analysis has been extended with the energy savings and income generation on various reconfiguration methods under various partial shade conditions. The more energy savings and income generation compared to the existing reconfiguration methods show its adaptability in real-time implementation. The outcomes of the proposed research work are as follows: (i) less wiring line losses along with the less renumbered PV modules of around 39.5%, (ii) developing a simple non-puzzle-based reconfiguration technique to reduce the complexity in implementation, and (iii) improved efficiency with enhanced power generation. To show the effectiveness and usefulness of the SAT reconfiguration, a comparative assessment with the conventional puzzle-based methods is developed with various performance indices.
13 July 2021 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
As solar energy extraction becomes more and more popular, attempts are made to further improve the efficiency and reliability of such systems. At the time of partially shaded conditions, the peak power that can be extracted from the PV modules may be more, but the conventional control algorithms may result in the underutilization of the panel. The Maximum Power Point Tracking (MPPT) algorithms like Perturb and Observance (P&O), Incremental Conductance, and other conventional methods fail to detect the global maximum power point (GMPP). In such conditions, a GMPP algorithm is recommended. This paper proposes a new GMPP algorithm called Krill-Herd (K-H) to augment the performance of PV modules with non-uniform irradiations. Krill is a marine animal, and researchers have shown keen interest in this herd due to its ability to form large swarms. The hardware experimentation with a highly efficient Interleaved Boost Converter (IBC) with GaN devices under different partially shaded conditions is used to validate the proposed algorithm. IBC has many advantages over conventional boost converters such as low input current ripple, high efficiency, fast transient response, and improved reliability, less current stress on switching devices, and reduction in filter size. The K-H algorithm shows improved performance over the conventional P&O based algorithms with no oscillations around peak power point, less time to reach steady-state, less power loss, more accuracy, and fewer numbers of iterations. Five different conditions of operation of the panels in real time applications have been considered and is demonstrated that higher efficiency levels of around 99% could be obtained using the K-H algorithm in all these cases.
16 February 2022 in Distributed Generation & Alternative Energy Journal
The focus on reduction of converter size in nanogrid connected Photo-Voltaic(PV) systems increases to obtain the various advantages. This paper proposesa single stage nanogrid connected solar PV system that works with DC-ACinverter along with the closed loop control strategy to send the maximumpower from the PV array. The proposed scheme controls the power deliveryof the PV system to nanogrid in a single stage power conversion along withthe incorporated Maximum Power Point Tracking (MPPT) controller. Thedecoupled control strategy has been designed and developed for the proposedsystem using synchronous reference frame theory. The developed hardwareprototype in the laboratory has been used to validate MATLAB/Simulink sim-ulation results. The simulation and experimental results have been observed for dynamic changes in irradiation by maintaining the Total Harmonic Dis-tortion (THD) within the standard limits while operating at unity powerfactor. The successful validation of the proposed control strategy shows itsusefulness in real-time nanogrid applications.