High-density polyethylene (HDPE) is a valuable material, but its application under certain operational conditions is limited by oxidation resistance. To mitigate this, rice husk ash (RHA), a silica-rich (~95%) byproduct, was incorporated as a reinforcing filler. This study evaluates the effect of electron beam (EB) irradiation, at doses up to 100 kGy, on the properties of HDPE/RHA composites, focusing on mechanical performance and the polymer–filler interface. The results demonstrate that EB irradiation induces crosslinking and enhances interfacial interaction between the HDPE matrix and RHA filler. While the overall tensile strength of neat HDPE tended to decrease with irradiation dose (from 28.5 ± 1.2 MPa to 24.1 ± 1.5 MPa at 100 kGy), the optimization of dose and filler contents produced notable results: A maximum tensile strength of 29.0 ± 1.1 MPa was achieved in the composite containing 5 wt% RHA at 75 kGy. Furthermore, irradiation stabilized the material’s behavior, resolving the heterogeneous dispersion observed in non-irradiated samples with low RHA content. Regarding toughness, Izod’s impact resistance increased from 3.2 ± 0.2 kJ/m2 to 3.7 ± 0.3 kJ/m2 for the 10 wt% RHA composites irradiated at 50 kGy. Statistical analysis (ANOVA, p < 0.05) confirmed the significance of these changes. In conclusion, electron beam irradiation is an effective tool for optimizing the mechanical properties and performance uniformity of HDPE/RHA composites, making them promising candidates for applications requiring enhanced durability and consistency, such as food packaging.
Graphene nanoparticles (GnP) were selected as an alternative reinforcing nanofillers, which enhances the mechanical properties of polypropylene (PP-homo and PP-block copolymer). It may play the role of compatibilizer in polypropylene-graft-maleic anhydride (PP-g-MA) from a double-screw extruder. The effect of GnP loading and the use of the PP-g-MA compatibilizer were studied. The influence on the mechanical properties of tensile strength, elongation at break, IZOD impact strength, and melting temperature in PP-homo and PP-block copolymer were investigated and compared. Their improvement was observed at to a certain amount of 0.3% (by mass) of GnP depending on the substrate nature: homopolymer or block copolymer. The increase from 69.3 J.m-1 to 176.0 J.m-1 corresponds to a 2.5 times rising in IZOD impact resistance for block copolymer. The PP block copolymer has a significant affinity in respect of the presence of graphene and the compatibilizer due to the elastomeric co-monomer present in the block copolymer.
30 September 2019 in Revista Brasileira de Ciência, Tecnologia e Inovação
A eutrofização é um dos principais problemas ambientais da atualidade e vem afetando diversos mananciais no Brasil e no mundo. O processo é caracterizado pelo aumento da biomassa dos produtores primários em decorrência das altas concentrações de nutrientes, em especial, do fósforo (P), tendo como principais consequências: perda da biodiversidade e aumento dos custos do tratamento da água. Apesar das consequências indesejáveis da eutrofização, o P é um elemento químico essencial à produção de alimentos e suas fontes naturais estão se esgotando. Desse modo, o reaproveitamento do fósforo é de extrema importância para a manutenção da vida. Assim, o presente estudo teve como objetivo avaliar e comparar o acúmulo de fósforo em biofilme formado sobre lâminas de vidro e de filme polimérico biodegradável (Ecovio®modificado), com o intuito de desenvolver tecnologia mitigadora do processo de eutrofização e que permitao reaproveitamento do fósforo (suporte biodegradável).Para tanto, lâminas de vidro e do filme poliméricobiodegradável (14 cm²) foram fixadas em estruturas flutuantes (n = 3) instaladas na subsuperfície de ambiente hipereutrófico (Lago das Garças), onde permaneceram por um período de 30 dias. Foram determinados os teores de fósforo total do biofilme e realizado o monitoramento de parâmetros de qualidade da água. O acúmulo de fósforo sobre o filme polimérico biodegradável (24,4 mg.g-1; 698,8 mg.m-2) foi superior ao do vidro (8,0 mg.g-1; 169,1 mg.m-2) e as taxas de acúmulode P foram superiores aos valores disponíveisem literatura. Dessa forma, a tecnologia vem se mostrando promissora para a mitigação do processo de eutrofização e recuperação de fósforo.
Influence of electron beam irradiation on the mechanical properties of PBAT/PLA polymeric blend / Influência da irradiação do feixe de elétron nas propriedades mecânicas da mistura polimérica PBAT/PLA
Plastic waste contributes negatively to the environment by increasing space occupation, creating health hazards on land, in the air, and at sea. For this reason, they need to be disposed of properly so that they can be recycled efficiently. To combat these impacts and reduce environmental pollution, this project aims to study the recycling process of polypropylene (PP) from industrial waste scraps and polypropylene from urban solid waste (MSW) using ionizing radiation from 0 to 500 kGy. Irradiation processing showed efficiency when compared to other recycling processes, promoting the molecular shearing of PP, reaching ideal lengths of shorter chains to be used as a carrier for additives for adhesives and plastics, and/or to be used as a flow modifier for injecting parts. Ionizing radiation above 100 kGy initiated the formation of cross-links, cross-linking the PP that could be used as fillers for asphalt, construction, and other applications, or as a fuel energy source, contributing to the ecosystem, without changes in the curly lettuce after ecotoxicity tests. The use of ionizing radiation in polymer processing has a great advantage when compared to other plastic recycling systems.