Błażej Bartoszewicz

Błażej Bartoszewicz

Auto-generated profile, based on publicly available information

Błażej Bartoszewicz

Faculty of Mechanical Engineering, Bialystok University of Technology, 45C Wiejska, 15-351 Bialystok, Poland

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 September 2019 in Nonlinear Dynamics
Verified
Journal Article
Open access
PDF file
RGRafał Grądzki
Rafał Grądzki
ZKZbigniew Kulesza
Zbigniew Kulesza
BBBlazej Bartoszewicz
Blazej Bartoszewicz
Rotating machines are exposed to different faults such as shaft cracks, bearing failures, rotor misalignment, stator to rotor rub, etc. Therefore, turbo-generators, aircraft engines, compressors, pumps, and many other rotating machines should be constantly diagnosed to warn about the probable appearance of a possible rotor failure. Unfortunately, despite the ongoing work on various rotor fault detection methods, there are still very few techniques that can be considered as reliable and applicable in practical problems. The difficulty lies in the fact that usually the fault introduces very subtle local changes in the overall structure of the rotor. The symptoms of these changes must be isolated and extracted from a wide spectrum of vibration data obtained from sensors measuring the vibrations of the machine. The measured data are usually disturbed with some noise or other disturbances, and that is why the detection of a possible rotor fault is even more difficult. The paper presents a new rotor fault detection method. The method is based on a new diagnostic model of rotor signals and external disturbances. The model utilizes auto-correlation functions of measured rotor’s vibrations. By proper processing of the measured vibration data, the influence of environmental disturbances is completely compensated and reliable indications of the possible rotor fault are obtained. The method has been tested numerically using the finite element model of the rotor and then verified experimentally at the shaft crack detection test rig. The results are presented in a readable graphical form and confirm high sensitivity and reliability of the method.

28 October 2023 in Materials
Verified
Journal Article
Open access
PDF file
JGJulia Magdalena Głowacka
Julia Magdalena Głowacka
ŁDŁukasz Derpeński
Łukasz Derpeński
MFMiłosz Frydrych
Miłosz Frydrych
BSBogna Sztorch
Bogna Sztorch
BBBłażej Bartoszewicz
Błażej Bartoszewicz
Robert Edward PrzekopRobert Edward Przekop
Robert Edward Przekop
This article presents the development of an automated three-point bending testing system using a robot to increase the efficiency and precision of measurements for PLA/TPU polymer blends as implementation high-throughput measurement methods. The system operates continuously and characterizes the flexural properties of PLA/TPU blends with varying TPU concentrations. This study aimed to determine the effect of TPU concentration on the strength and flexural stiffness, surface properties (WCA), thermal properties (TGA, DSC), and microscopic characterization of the studied blends.

1 January 2018 in Shock and Vibration
Verified
Journal Article
Open access
PDF file
RGRafał Grądzki
Rafał Grądzki
PLPaweł Lindstedt
Paweł Lindstedt
ZKZbigniew Kulesza
Zbigniew Kulesza
BBBłażej Bartoszewicz
Błażej Bartoszewicz
In this work, an innovative diagnosis method of rotor blades is presented. A measurement signal of blade tip displacement is divided into two observation zones, in which two peaks of an additional template signal are introduced. Cross‐correlation and power spectral density functions of the measurement and template signals in these two distinct zones are calculated. Next, the phase shift between the two cross‐correlation functions is obtained by calculating the ratio of the two power spectral density functions. The changes in parameters of an analytical description of this phase shift are used to determine a distinct and easy‐to‐analyze image of the technical condition of the tested blade. A graphical portrait indicating the technical condition of all blades in the annulus is developed. Although not directly measured, environmental signals (e.g., external disturbances and sensor’s noise) affecting the diagnostic process are included in the method. It is demonstrated that, by using the proposed signal processing technique, a negative influence of these disturbances is eliminated and the reliability of the machine technical condition indications is improved. The approach is demonstrated using experimental results of turbine engine blade displacements. High effectiveness of the method and measurement equipment has been confirmed in a wide range of analyzed tip‐timing results obtained in different periods of the measurement process.

8 February 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
RGRafał Grądzki
Rafał Grądzki
BBBłażej Bartoszewicz
Błażej Bartoszewicz
EMEmiliano Martinez
Emiliano Martinez
The article presents an adaptation of a parametric diagnostic method based on the square of the amplitude gains model, which was tested in experimental studies on bearing damage detection (outer race, inner race, bearing balls damage). The described method is based on the shaft displacement signal analysis, which is affected by vibrations coming from the bearings. The diagnostic model’s parameters are determined by processing the signal from the time domain to the frequency domain in a few steps. Firstly, the recorded signal is divided into two observation periods, next the analytical autocorrelation functions are determined and approximated by a polynomial. Then, the diagnostic thresholds are adopted, and the model parameters are converted into damage maps that are easy to interpret and assess the technical condition of the bearings. The presented method shows the technical condition of bearings in a qualitative way. Depending on the received color damage maps, it is possible to determine their level of wear. Green and blue indicate poor wear or no damage, red indicates increased wear, and black clearly indicates a damaged bearing.

7 February 2025 in Aerospace Science and Technology
Verified
Journal Article
Closed access
Krzysztof Kamil ŻurKrzysztof Kamil Żur
Krzysztof Kamil Żur
JYJinjin Yuan
Jinjin Yuan
HGHULUN GUO
HULUN GUO
ZCZhenyu Cheng
Zhenyu Cheng
BBBłażej Bartoszewicz
Błażej Bartoszewicz

15 February 2017 in Journal of Vibroengineering
Verified
Journal Article
Open access
MCMariusz Czajkowski
Mariusz Czajkowski
BBBłażej Bartoszewicz
Błażej Bartoszewicz
ZKZbigniew Kulesza
Zbigniew Kulesza
Modal analysis of a flexible, non-rotating rotor with a crack in a shaft is presented. The Jeffcott model of the rotor consists of the massless shaft and a disk concentrating the mass of the full system. The model includes ball bearings supporting the shaft and the model of the transverse shaft crack located near the disk. Simulation results present changes in natural frequencies of the system with the changing angular position of the rotor. Those changes are observed as doubled natural frequency peaks in the rotor's frequency responses. They appear only for the cracked rotor and can be explained by shaft stiffness changes due to the opening and closing of crack faces under gravity. The results of the conducted numerical analyzes demonstrate that these doubled frequency peaks can be used for early shaft crack detection.