1 January 2024 in Reviews on Advanced Materials and Technologies
This short review summarizes mechanical interactions occurring in polymer with carbon nanotubes. The work contains a detailed discussion of methods for improving the mechanical characteristics of polymer composites with carbon nanotubes, for which both experimental and computational work in this area are presented. The paper discusses in detail such methods of improving the connection between carbon nanotubes and the polymer as functionalization (covalent and non-covalent), enhancement by embedded nanoparticles and structural modification of the matrix. The review focuses on the molecular dynamics method as one of the promising methods for studying mechanical interactions in polymer composites with carbon nanotubes.
13 October 2023 in Kondensirovannye sredy i mezhfaznye granitsy = Condensed Matter and Interphases
The article presents the results of the study of the mechanical properties and defect structure of gallium oxide (Ga2O3) by using the piezoelectric composite oscillator technique. Bulk samples of the Ga2O3 beta phase in the form of single crystals and their intergrowths were obtained by growth from a melt with a shaper (Stepanov technique). The research involved studying the dependences of the longitudinal elastic modulus and the damping of elastic vibrations at a frequency of 100 kHz on the strain amplitude. Changes in the elastic and microplastic properties of the samples at different temperatures were attributed to possible relaxation phenomena in the structure of the material. Studying the defect structure in samples of pure and doped Ga2O3 is necessary to improve the technology for the production of large single crystals. The fundamental questions in this area are the influence of defects on the anisotropy of electrical conductivity, band structure, and other functional properties of the resulting semiconductor material. The purpose of this article is to establish the features of sample preparation, research, and interpretation of the results obtained by the piezoelectric composite oscillator technique for gallium oxide samples. In the studied samples, the first longitudinal vibration mode was excited, which corresponded to a length of about 27 mm and a small cross-section of the sample. The temperature dependences in the region of low and high strain amplitudes were determined separately. The crystalline quality of the prepared samples was assessed by X-ray diffraction with the analysis of the rocking curve. The value of Young’s modulus obtained along the growth axis (crystalline orientation ) in Ga2O3 crystals E≈260 GPa is in line with the results of previous studies. Relaxation peaks corresponding to various dislocation interactions were found on the temperature dependences of internal friction at a temperature of 280 K В статье приводятся результаты исследования механических свойств и дефектной структуры оксида галлия (Ga2O3) при помощи метода составного пьезоэлектрического осциллятора. Объёмные образцы бета фазы Ga2O3 в виде монокристаллов и их сростков были получены при помощи роста из расплава с формообразователем (метод Степанова). Исследовались зависимости модуля продольной упругости и затухания упругих колебаний на частоте 100 кГц от амплитуды деформации. Изменения упругих и микропластических свойств образцов при различной температуре были сопоставлены с возможными релаксационными явлениями в структуре материала. Изучение дефектной структуры в образцах чистого и легированного Ga2O3 необходимо для совершенствования технологии получения монокристаллов большого размера. Фундаментальными вопросами в данной области являются влияние дефектов на анизотропию электропроводности, зонную структуру и другие функциональные свойства получаемого полупроводникового материала. Цель данной статьи в установлении особенностей подготовки образцов, проведении исследований и интерпретации результатов, полученных методом составного пьезоэлектрического осциллятора для образцов оксида галлия. В исследуемых образцах возбуждалась первая продольная мода колебаний, что соответствовало длине около 27 мм и малому поперечному сечению образца. Отдельно определялись температурные зависимости в области низких и высоких амплитуд деформаций. Для оценки кристаллического совершенства образцов, подготовленных для исследований, использовалась рентгеновская дифракция с анализом кривой качания