Luca Colombo

Luca Colombo

Auto-generated profile, based on publicly available information

Luca Colombo

Institute for NanoSystems Innovation (NanoSI) Northeastern University Boston Massachusetts USA

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 September 2023 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Open access
GGGabriel Giribaldi
Gabriel Giribaldi
LCLuca Colombo
Luca Colombo
MRMatteo Rinaldi
Matteo Rinaldi
This paper reports on 30% Scandium-doped Aluminum Nitride (ScAlN) Lateral Field-Excited (LFE) Cross-sectional Lame’ Mode Resonators (CLMRs) with unprecedented performance in the 6-20 GHz range. By combining high-crystallinity 30% ScAlN piezoelectric thin-films, a lithographic tunability of the resonance frequency, and a simple 3-mask post-CMOS compatible fabrication process, we propose a technology platform that can enable the mass-production of low-loss, wide-band, and compact microacoustic filtering devices spanning a wide spectrum portion on the same chip for the next-generation RF front-ends of handsets. The present work demonstrates a successful scaling of the microacoustic technology well beyond the sub-6 GHz 5G band, as well as the outstanding capabilities of high-crystallinity 30% ScAlN piezoelectric layers in delivering high-quality factor ( Q ) and high-electromechanical coupling ( k t 2 ) resonators, notably exceeding the state-of-the-art in terms of relevant figures of merit. Furthermore, we experimentally investigate the impact of geometrical parameters such as tethering configuration and width-over-length ratio on the devices’ 3dB quality factor ( Q 3dB ), power linearity, and Temperature Coefficient of Frequency (TCF). By adopting a statistical approach for data analysis, we determine the optimal geometry to maximize the Q . Moreover, we experimentally demonstrate that a fully tethered device’s configuration ensures superior power linearity, lower TCF, and higher device yield, and select that as best design trade-off between all the variables under consideration. Finally, we discuss a further scaling of LFE CLMRs, both in terms of higher doping levels in the piezoelectric layer, in order to enhance the performance of microacoustic filters, and in terms of higher operation frequencies, in order to reach and cover the mm-waves spectrum.

22 June 2018 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
LCLuca Colombo
Luca Colombo
AKAbhay Kochhar
Abhay Kochhar
GVGabriel Vidal-Álvarez
Gabriel Vidal-Álvarez
GPGianluca Piazza
Gianluca Piazza
This letter reports on the design, fabrication, and testing of an X-cut lithium niobate laterally vibrating resonator operating around 50 MHz and exhibiting a record figure of merit-FoM = product of electromechanical coupling (kt²) and quality factor at a resonance (Qs)- of 1560. For practical applications, the individual resonator is arranged in a large array so as to achieve a static capacitance around 1 pF, while still preserving a high FoM of 570. Modeling of anchor losses through finite element analysis is used to guide the design of these resonators, which simultaneously exhibit high electromechanical coupling (kt² > 30%) and high quality factor (Qs > 5000) in vacuum.l [2018-0097]

7 February 2020 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Closed access
LCLuca Colombo
Luca Colombo
AKAbhay Kochhar
Abhay Kochhar
GVGabriel Vidal-Álvarez
Gabriel Vidal-Álvarez
GPGianluca Piazza
Gianluca Piazza
This paper reports on the modeling, design, fabrication, and testing of high-performance X-cut Lithium Niobate (LN) Laterally Vibrating Resonators (LVR) operating around 50 MHz. The objective of this work is to exploit the high Figure of Merit (FoM) –product of quality factor at series resonance (Qs) and electromechanical coupling (kt2)– to provide for large passive voltage amplification in the front-end of emerging radio frequency (RF) applications –i.e., Wake-Up Radio Receivers (WuRx). Finite Element Analysis (FEA) is performed to optimize devices’ geometry and ensure simultaneous high Qs and kt2. Resonators exhibiting Qs > 5,300 and kt2 > 27% are demonstrated, with FoM > 1,650 –the highest recorded for resonators in the MHz range to the authors’ knowledge. Finally, passive voltage gains between 35 V/V and 57 V/V are showcased for capacitive loads ranging from 400 fF to 1 pF.

20 September 2022 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
LCLuca Colombo
Luca Colombo
AKAbhay Kochhar
Abhay Kochhar
GVGabriel Vidal-Álvarez
Gabriel Vidal-Álvarez
PSPietro Simeoni
Pietro Simeoni
USUmut Soysal
Umut Soysal
GPGianluca Piazza
Gianluca Piazza
This paper reports on the design, fabrication, and characterization of $S_0$ mode X-cut Lithium Niobate Laterally Vibrating Resonators (LVRs) operating between 100 MHz and 1 GHz. In the first section of this work, analytical and numerical models are implemented to investigate the impact of topology and geometrical features on the Electromechanical Coupling ( $k_t^2$ ) and Quality Factor ( $Q_s$ ) of this class of devices. The models are used to define the design of experiments aimed at characterizing the resonator performance. The resonators are fabricated and tested in atmospheric, vacuum, and cryogenic ( $T$ = 10 K) conditions to assess their performance and identify the main sources of discrepancies in $k_t^2$ and $Q_s$ with respect to the analytical and numerical models. Under vacuum quality factors exceeding a few thousands are recorded across the investigated spectrum, with measured $k_t^2$ as high as 28.9 $\%$ . At 100 MHz, measured $Q_s$ and $k_t^2$ of 8,279 and 28.5 $\%$ , respectively, combine into a record-breaking Figure of Merit ( $FOM$ ) of 2,688, while cryogenic testing highlighted $Q_s$ as high as 26,511. In the last section, by analyzing the differences in $k_t^2$ and $Q_s$ between experiments and models, best design approaches to maximize the $FOM$ and minimize spurious modes responses are reported, with a focus on the 100 to 550 MHz range.2022-0081

6 April 2020 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
XZXuanyi Zhao
Xuanyi Zhao
LCLuca Colombo
Luca Colombo
CCCristian Cassella
Cristian Cassella
In the last few decades, bulk-acoustic-wave filters have been essential components of 3G-to-4G radios. These devices rely on the high electromechanical coupling coefficient (kt2 ∼ 7%), attained by aluminum nitride (AlN) film-bulk-acoustic-resonators (FBARs), to achieve a wideband and low-loss frequency response. As the resonance frequency of FBARs is set by their thickness, the integration of multiple FBARs, to form filters, can only be attained through the adoption of frequency tuning fabrication steps, such as mass loading or trimming. However, as the ability to reliably control these steps significantly decays for thinner (or higher frequency) FBARs, manufacturing FBAR-based filters, addressing the needs of emerging IoT and 5G applications, is becoming more and more challenging. Consequently, there is a quest for new acoustic resonant components, simultaneously exhibiting high-kt2 and a lithographic frequency tunability. In this work, a novel class of AlN resonators is presented. These radio frequency devices, labeled as two-dimensional-resonant-rods (2DRRs), exploit, for the first time, the unconventional acoustic behavior exhibited by a forest of locally resonant rods, built in the body of a profiled AlN layer that is sandwiched between a bottom un-patterned metal plate and a top metallic grating. 2DRRs exhibit unexplored modal features that make them able to achieve high-kt2, a significant lithographic frequency tunability, and a relaxed lithographic resolution, while relying on an optimal AlN crystalline orientation. The operation of 2DRRs is discussed, in this work, by means of analytical and finite-element-methods. The measured performance of the first fabricated 2DRR, operating around 2.4 GHz and showing a kt2 in excess of 7.4%, is also reported.

7 March 2019 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
AKAbhay Kochhar
Abhay Kochhar
MGMary E. Galanko
Mary E. Galanko
MSMazen Soliman
Mazen Soliman
HAHoda Abdelsalam
Hoda Abdelsalam
LCLuca Colombo
Luca Colombo
GPGianluca Piazza
Gianluca Piazza
This paper reports a practical demonstration of a proposed resonant microelectromechanical receiver for low power wake-up receiver (WuRx) applications. The proposed system is made of three main components: a piezoelectric based acoustic resonator, an electrostatically-driven MEMS resonant demodulator, and a CMOS baseband trigger circuit. The filtering, amplification, and demodulation of the incoming signal are performed through the piezoelectric resonator and the resonant demodulator, ensuring zero power consumption for both the radio frequency (RF) and mixing stages. The only power consumption occurs at baseband by operating the CMOS circuit in deep subthreshold. This system utilizes a lithium niobate piezoelectric resonator possessing a figure of merit of around 650 and achieving voltage gain of 28 dB. A resonant demodulator fabricated in the Epi-Seal MEMS process is utilized to attain a conversion efficiency of 13.8 nA/V². In the trigger circuit, an amplifier with transimpedance >200 MΩ is utilized to sense the output current from the demodulator. An intermediate buffer and a multiple stage passive latch rectifier are utilized to generate the wake-up signal through a Schmitt trigger. The demonstrated system achieves -40.2 dBm sensitivity for a 44 kHz amplitude-modulated 50 MHz RF signal while consuming 38.75 nW. This architecture is a promising step toward a WuRx capable of achieving higher interference rejection, high sensitivity, and nW range power consumption at a high data rate. [2018-0261]