6 November 2024 in IEEE Transactions on Power Electronics
The traditional method for achieving misalignment tolerance using two detuned circuits depends on output sampling and communication between the primary and secondary sides. This paper proposes a self-adaptive dual-channel detuned compensation topology to achieve a stable output for wireless charging of autonomous underwater vehicles (AUVs). In the low coupling coefficient interval, power is transferred through both channels; in the high coupling coefficient interval, power is transferred through only one channel. The mode switching process occurs naturally without additional switches or control. Two sets of arc-shaped coils are employed as the two channels, forming dual arc-shaped coil sets, without cross-coupling between them. Due to the symmetrical magnetic couplers, the mutual inductances of the two channels respond similarly to both rotational and axial misalignment. A 1.6-kW experimental prototype for the AUV wireless charging is built to validate the feasibility of the proposal. The output voltage fluctuation of the system is 8% within the coupling coefficient interval of [0.2, 0.6]. The system can still maintain over 89% transmission efficiency in the worst case.
9 December 2024 in IEEE Transactions on Power Electronics
In the medium- and high-capacity power applications, typically multiple switches connected in series and parallel are used in power electronic converters to handle high voltages and currents. Powering the driving circuits and auxiliary units with high insulation requirements is challenging. This article proposes a modular multi-output wireless power transfer (WPT) system with constant-current (CC) output characteristics for auxiliary power supply. Compared with conventional solutions, there is no need for complex control circuits and much magnetic material. The dual-frequency topology with CC outputs is derived by applying the analytical method that used to obtain the dual-frequency topology with constant-voltage (CV) outputs. The conditions for the system to maintain zero phase angle (ZPA) at different frequencies are discussed. Lower output fluctuations than single-frequency multi-output systems and dual-frequency CV output systems are verified. A magnetic coupler with integrated compensation inductors is designed to eliminate the need for discrete inductors and improve the power density. An experimental prototype is built to verify the validity of the theory. The WPT system achieves an output current fluctuation of no more than 4.78%, a maximum system efficiency higher than 85%, and an output power of more than 10 W at a single port, which can well meet the requirements of auxiliary power supply.
28 October 2025 in IEEE Transactions on Power Electronics
In an electric vehicle (EV) wireless power transfer system, a critical challenge is to address mutual inductance variations and output fluctuations caused by the misalignment along the lateral direction of the EV. This letter proposes an antimisalignment method using two transmitting coils. First, an inductor–capacitor–capacitor series topology is adopted on the transmitting side. The relationship between the output voltage and the mutual inductance is derived, and a compensation parameter design method is proposed. Second, an output voltage compensation method is proposed to enhance the misalignment tolerance performance. Finally, an experimental prototype is built to verify the validity of the theory. The experimental results show that the proposed system can achieve an output performance of 200 V and 1 kW, with a peak efficiency of 95.17% over the misalignment range.
21 December 2023 in IEEE Transactions on Power Electronics
In wireless power transfer (WPT) systems for electric vehicles (EVs), the coil misalignment is inevitable in most charging situations. Most present studies concentrate on the misalignment tolerance on one direction, either on the X, Y, Z, or diagonal directions, but lack the misalignment tolerance on the whole charging plane. In this paper, a reconfigurable adaptive topology and centrosymmetric coils are proposed to achieve misalignment tolerance over the whole charging plane. By switching among three operation modes of the proposed reconfigurable topology at the different misaligned regions, the output voltage at the boundary regions can be increased and the output voltage fluctuation can be limited. Firstly, the mathematical model of the proposed reconfigurable adaptive topology in the different operation modes are investigated. Secondly, the design process of the magnetic coupler and the characteristics of the centrosymmetric coils are presented. Finally, a 926-W prototype is built to verify the proposed system. The experimental results demonstrate that the fluctuation of the output voltage is less than 21.3% apart from the four most corner regions, and the peak efficiency is 84.5%.
8 November 2024 in IEEE Transactions on Industrial Electronics
For urban pipelines, in-pipe robots are used for routine maintenance and inspection, but they are difficult to charge. To address this need, this article proposes a modular reconfigurable wireless power transfer (WPT) system with multiple constant-voltage (CV) and constant-current (CC) hybrid outputs. The proposed system consists of a power module and several load modules in cascade, with each load module not only acting as a receiver to provide power to the output but also acting as the power relay to transfer energy to the succeeding modules. The introduction of a reconfigurable structure allows the loads to achieve a CV output or a CC output independently, while realizing zero voltage switching and high efficiency. Various decoupling methods are utilized to integrate the compensation inductors into the couplers. A WPT experimental prototype is constructed to verify the feasibility of the proposed system. The output has the capability to achieve a CV output or a CC output, with a maximum fluctuation rate of 2.88% and a maximum efficiency of over 97%.
31 May 2024 in IEEE Transactions on Power Electronics
In some industrial application scenarios, multiple constant-voltage (CV) outputs with galvanic isolation are required. Selective power transfer among the CV outputs can enable its flexibility. This paper proposes a modular singlechannel wireless power transfer system for industrial power supply with a dual-frequency hybrid compensation topology. The series-series topology is adopted for CV outputs at the two CV output frequency points. The band-stop filter with a parallel resonant network is designed to filter the undesired frequency component and the series series-parallel resonant network is formed to avoid the impact of the band-stop filter on the desired frequency component. In this way, selective power transfer with CV outputs can be achieved by changing the working frequency. The mathematical model of the proposed compensation topology is established and analyzed. The transmission coils and the compensating inductors are integrated to achieve a compact structure. The design principles of the coupler parameters are proposed and a design example is given. An experimental prototype is built to verify the theoretical analysis. The system realizes CV outputs and supplies power to different loads at different working frequencies, with an average transfer efficiency of 85.23% and a maximum output power of 85.95 W