28 October 2025 in IEEE Transactions on Power Electronics
In an electric vehicle (EV) wireless power transfer system, a critical challenge is to address mutual inductance variations and output fluctuations caused by the misalignment along the lateral direction of the EV. This letter proposes an antimisalignment method using two transmitting coils. First, an inductor–capacitor–capacitor series topology is adopted on the transmitting side. The relationship between the output voltage and the mutual inductance is derived, and a compensation parameter design method is proposed. Second, an output voltage compensation method is proposed to enhance the misalignment tolerance performance. Finally, an experimental prototype is built to verify the validity of the theory. The experimental results show that the proposed system can achieve an output performance of 200 V and 1 kW, with a peak efficiency of 95.17% over the misalignment range.
21 January 2026 in IEEE Transactions on Industrial Electronics
To address the offset issue in the field of wireless power transfer, a wireless charging system based on dynamic phase-shift controlled dual-transmitting coils is proposed in this letter. The proposed system splits the traditional single-transmitting coil into two independent coils and adopts the LCC-S compensation topology. When the receiving coil is slightly offset, only the primary transmitting coil operates; as misalignment increases, the system smoothly switches to dual-transmitting coil mode by adjusting the phase-shift angle of the secondary inverter, thereby maintaining stable output. Theoretical analysis indicates that the output voltage can be compensated for changes in mutual inductance through phase-shift control. Experimental validation shows that the proposed system maintains stable and efficient output under misalignment conditions. Compared with the traditional solutions, the proposed scheme offers a more promising solution for the offset issue.
22 April 2022 in IEEE Access
This paper proposes a novel branch voltage-balancing control strategy for a hexagonal converter (Hexverter). First, the state-space model based on the double- dq transformation is analyzed in-depth along with the necessary basic mathematical derivation, and the active/reactive power control model in the dq reference frame for the Hexverter is proposed. Second, a zero-sequence double-loop network consisting of a Y-loop and a Hex-loop circulating current was established. This study proposes a method to suppress the Y-loop circulating current by connecting a capacitor at the neutral point. We then establish a novel branch voltage-balancing control strategy based on the transfer power model. The essence of the proposed control strategy is to control the charging and discharging states of each submodule via the zero-sequence voltages and the Hex-loop circulating current to regulate the power transfer between adjacent submodules and branches, thereby effectively ensuring the dynamic balance of the DC voltages of the submodules. The branch voltage-balancing control model and power control model proposed in this paper are based on zero-sequence and positive-sequence networks, respectively. The relative independence of the positive- and zero-sequence networks leads to decoupling of the branch voltage-balancing control model and the power control model; thus, the respective control objectives can be achieved by adjusting the respective control variables independently. It has a stronger adaptability to diverse power grid operating parameters. Finally, the validity and correctness of the mathematical model and control strategy proposed in this study are verified using MATLAB/Simulink.
23 October 2025 in IEEE Access
When dealing with the compatibility issues of the coupling structure in the wireless power transfer (WPT) system for electric vehicles (EVs), there mainly exist unipolar (Q) and bipolar (DD) coils. There is no direct energy transmission between the two, which leads to the interoperability of coupling structures. During the charging process, misalignment often occurs between the transmitter (Tx) and the receiver (Rx). The interoperability and misalignment tolerance of EV WPT system need to be addressed. To solve these problems, a novel symmetrical bipolar coil structure is proposed, which can work as Tx and Rx. The proposed structure is based on the internal structure of the Q coil, through proportional division and the method of finite element design, a novel symmetrical bipolar coil structure with self-decoupling was finally obtained. An experimental prototype of 1.3-kW was established to verify the proposed. The interoperability and misalignment tolerance performance of the proposed coil at Rx were verified through calculation, simulation and experiments. Meanwhile, a corresponding dual experimental proto-type was also built, taking the proposed coil structure as Tx. At the same time, the interoperability performance and misalignment tolerance performance of the proposed coupling structure were also verified.
29 May 2026 in IEEE Transactions on Industrial Electronics
Uncrewed aerial vehicles (UAVs) have integrated into a variety of fields. To increase the operational longevity and load capacity limited by the battery capacity, mid-course wireless power transfer (WPT) for recharging is applied. However, the stability of the output is destabilized by the significantly variation in the mutual inductance resulting from the misalignment of coils. A free-position WPT system for lightweight UAV based on multireceiver-coil design is proposed in this letter. Three sets of receiver (Rx) coils are designed to receive flux in horizontal and vertical directions. The Rx coils are assigned to two rectifiers connected in series on the DC side so that the equivalent mutual inductance is the positive summation of all the mutual inductances. In this way, the output is maintained stable when misalignment occurs. An experimental prototype is established to verify the proposed WPT system. The results have revealed that the output voltage fluctuation is only 8.15% within the circular area of 120 mm radius, with any horizontal and rotational misalignment.
29 September 2025 in IEEE Transactions on Transportation Electrification
In wireless power transfer (WPT) systems, the entry of metal objects (MOs) can lead to the generation of eddy currents within the MOs due to the strong magnetic field, posing a fire risk. To address this challenge, this article proposes a reconfigurable MO detection (MOD) circuit design, which aims to achieve blind-spot-free MOD using as few coils as possible. The reconfigurable circuits allow adjacent coils to be reconfigured into a bipolar (DD) structure, which can achieve detection without blind spots and ensure that the detection coils are always decoupled from the WPT system. An experimental platform for MOD is constructed in this article, and the results show that the MOD system has extremely weak coupling with the WPT system, enabling effective MOD blind spot detection even when the power transmission coil is displaced by 50 mm, and the proposed MOD system achieves a detection height of 7 mm.