The unipolar, bipolar, and quadrupolar coils used in an electric vehicle wireless charging system are not interoperable with each other. Thus, there would be interoperability issues when the transmitting and receiving coils are not the same. To solve this issue, in this letter, we propose an asymmetrical quadrupolar coil that can be interoperable with the four conventional coils at the same position for efficient wireless power transfer, namely the unipolar coil, the bipolar coil along two perpendicular directions, and the quadrupolar coil. Large coupling coefficients can be achieved for the proposed coil with the four conventional coils when perfectly aligned. The misalignment performance with the four conventional coils is also investigated. An experimental prototype is developed to compare the conventional symmetrical quadrupolar coil with the proposed asymmetrical quadrupolar coil for validation of interoperability. The proposed asymmetrical quadrupolar coil achieves a maximum coupling coefficient of over 0.10 and a maximum dc–dc efficiency of over 85% with the four conventional coils.
19 December 2023 in IEEE Transactions on Power Electronics
Interoperability and misalignment tolerance issues are two urgent problems to be solved in electric vehicles wireless charging systems. To address these issues, a wireless power transfer (WPT) system based on decoupled mutually spliced double-D (DD) receiving coils is proposed in this article, which can achieve certain interoperability and antimisalignment performance. These two receiving coils are connected in series via the rectifiers on the dc side, resulting in the total equivalent mutual inductance equal to the sum of the absolute values of the mutual inductances between the transmitting coil and the two receiving coils. Compared with existing works, the proposed WPT system can achieve interoperability and misalignment tolerance with different transmitting coils: the square coil, the DD coil along the X- or Y -directions, and the quadrupole coil. A mathematical model and an experimental prototype are developed to verify the effectiveness of the proposed scheme, and the highest efficiency of the experimental prototype is 92.49%.
6 November 2024 in IEEE Transactions on Power Electronics
The traditional method for achieving misalignment tolerance using two detuned circuits depends on output sampling and communication between the primary and secondary sides. This paper proposes a self-adaptive dual-channel detuned compensation topology to achieve a stable output for wireless charging of autonomous underwater vehicles (AUVs). In the low coupling coefficient interval, power is transferred through both channels; in the high coupling coefficient interval, power is transferred through only one channel. The mode switching process occurs naturally without additional switches or control. Two sets of arc-shaped coils are employed as the two channels, forming dual arc-shaped coil sets, without cross-coupling between them. Due to the symmetrical magnetic couplers, the mutual inductances of the two channels respond similarly to both rotational and axial misalignment. A 1.6-kW experimental prototype for the AUV wireless charging is built to validate the feasibility of the proposal. The output voltage fluctuation of the system is 8% within the coupling coefficient interval of [0.2, 0.6]. The system can still maintain over 89% transmission efficiency in the worst case.
12 December 2024 in IEEE Transactions on Power Electronics
Electric vehicle charging platforms in the market are usually rated as 400 or 800 V, so the wireless charging system of electric vehicles must effectively supply power for these two voltage platforms. It is also an urgent problem to keep the output stable in the case of misalignment. The antioffset wireless charging system based on the reconfigurable coupling coupler is proposed. A coupling structure is reconfigured by a switch to charge a 400- or 800-V charging platform at the same power level. Simultaneously, an additional set of quadrupole receiving coils is connected in series to compensate for the reduced mutual inductance when offset occurs. To verify the proposed wireless power transfer system, a scaled-down experimental prototype was built. The results show that the highest dc–dc efficiency of the system is 93.66% and 94.27% at the voltage level of 200 and 400 V, respectively, and has good misalignment tolerance in two perpendicular directions.
8 January 2024 in IEEE Transactions on Transportation Electrification
The rapid development of electric vehicles (EVs) calls for an efficient and convenient charging method. Wireless power transfer (WPT) is favored by the academia and industry because of its convenience, security, and automation. However, there are still many problems to be solved, one of which is the interoperability issue between different coil types. In this article, an EV wireless charging system based on three decoupled non-overlapping unipolar transmitting coils is proposed. The inductor-capacitor-capacitor-series topology is adopted. The current directions of the three transmitting coils can be altered by adjusting the outputs of the three-phase independently controlled half-bridge inverter. In this way, the proposed transmitting coils can be tolerant with the unipolar coil and the two perpendicular bipolar coils, achieving interoperability and certain anti-misalignment capability with different receiving coils. The experimental results verify that the proposed system can achieve interoperability for both unipolar and bipolar coils and has misalignment tolerance in specific directions with a maximum efficiency of 93.67%.
21 December 2023 in IEEE Transactions on Power Electronics
In wireless power transfer (WPT) systems for electric vehicles (EVs), the coil misalignment is inevitable in most charging situations. Most present studies concentrate on the misalignment tolerance on one direction, either on the X, Y, Z, or diagonal directions, but lack the misalignment tolerance on the whole charging plane. In this paper, a reconfigurable adaptive topology and centrosymmetric coils are proposed to achieve misalignment tolerance over the whole charging plane. By switching among three operation modes of the proposed reconfigurable topology at the different misaligned regions, the output voltage at the boundary regions can be increased and the output voltage fluctuation can be limited. Firstly, the mathematical model of the proposed reconfigurable adaptive topology in the different operation modes are investigated. Secondly, the design process of the magnetic coupler and the characteristics of the centrosymmetric coils are presented. Finally, a 926-W prototype is built to verify the proposed system. The experimental results demonstrate that the fluctuation of the output voltage is less than 21.3% apart from the four most corner regions, and the peak efficiency is 84.5%.