Arup Kumar Debnath

Arup Kumar Debnath

Auto-generated profile, based on publicly available information

Arup Kumar Debnath

Department of Mechanical Engineering Khulna University of Engineering & Technology Khulna Bangladesh

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 October 2025 in Next Research
Verified
Journal Article
Closed access
TFTanvir Ahmed Fahim
Tanvir Ahmed Fahim
RERizuanul Arefin Emon
Rizuanul Arefin Emon
AKAbdullah Al Kafi
Abdullah Al Kafi
PNPronob Deb Nath
Pronob Deb Nath
ADArup Kumar Debnath
Arup Kumar Debnath
MHMd. Abdul Hasib
Md. Abdul Hasib

2 December 2025 in Next Materials
Verified
Journal Article
Open access
AMAbdullah Al Mahmud
Abdullah Al Mahmud
NNNushrat Bhuiyan Nishu
Nushrat Bhuiyan Nishu
ADArup Kumar Debnath
Arup Kumar Debnath
MHMd. Abdul Hasib
Md. Abdul Hasib
NRNiazur Rahim
Niazur Rahim
SUShihab Uddin
Shihab Uddin

3 May 2025 in Next Research
Verified
Journal Article
Closed access
ADArup Kumar Debnath
Arup Kumar Debnath
RMRubiat Mustak
Rubiat Mustak
SSSeam Shaikh
Seam Shaikh

1 January 2025 in Journal of Engineering
Verified
Journal Article
Open access
ADArup Kumar Debnath
Arup Kumar Debnath
MHMd. Abdul Hasib
Md. Abdul Hasib
RERizuanul Arefin Emon
Rizuanul Arefin Emon
AKAbdullah Al Kafi
Abdullah Al Kafi
TFTanvir Ahmed Fahim
Tanvir Ahmed Fahim
MRMd. Sanaul Rabbi
Md. Sanaul Rabbi
Fiber‐reinforced geopolymer composites (GPCs) are garnering heightened interest owing to their exceptional thermal stability and mechanical properties relative to traditional cement‐based systems. Kevlar and carbon–Kevlar hybrids are notably advantageous due to their exceptional tensile strength, low density, and ability to maintain structural integrity at extreme temperatures. This study examines the mechanical and physical properties of GPCs reinforced with Kevlar fiber (KF) and hybrid carbon–Kevlar fiber (CKF) under elevated temperatures. Geopolymers are typically brittle at high temperatures, but fiber reinforcement enhances their thermal and mechanical resilience. Samples with 1%, 1.5%, and 2% fiber content were heated to 200°C, 400°C, 600°C, and 800°C. Mechanical properties such as compressive and flexural strength, along with physical properties like color, cracks, and voids, were evaluated, and thermal conductivity was measured. For KF‐reinforced composites (KF‐GPCs), the highest compressive (14.6 MPa) and flexural strengths (10.02 MPa) were observed at 200°C with 1% fiber content. Strength decreased as the fiber content increased and temperatures rose, with partial recovery at 800°C, presumably owing to microstructural densification and phase transitions that briefly improved load‐bearing capability, although ductility remained markedly diminished. In CKF‐reinforced composites (CKF‐GPCs), compressive and flexural strength increased with fiber content, peaking at 200°C with 2% fiber (10.86 MPa). However, CKF‐GPCs showed increased brittleness and limited strain at 800°C. Thermal conductivity dropped significantly for both composites at 800°C (54.55% for KF‐GPC and 59.23% for CKF‐GPC). SEM analysis revealed stronger fiber–matrix bonding and lower porosity in KF‐GPCs compared to CKF‐GPCs, which exhibited higher porosity and fiber pullout.

13 February 2026 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
HMHayat Mahmud
Hayat Mahmud
RKRubaiya Khan
Rubaiya Khan
ADArup Kumar Debnath
Arup Kumar Debnath
MHMd. Abdul Hasib
Md. Abdul Hasib

12 May 2026 in SPE Polymers
Verified
Journal Article
Open access
NSNayan Sur
Nayan Sur
TNTitu Nath
Titu Nath
IZIshrak Ibn Zahid
Ishrak Ibn Zahid
ADArup Kumar Debnath
Arup Kumar Debnath
MHMd. Abdul Hasib
Md. Abdul Hasib
DRDurjoy Roy
Durjoy Roy
The development of sustainable, high‐performance materials has intensified the demand for natural fiber‐reinforced polymer (NFRP) composites. However, the inherent limitations of natural fibers, such as low interfacial bonding and high moisture absorption, necessitate advanced hybridization and filler modification. This study investigates the mechanical, physical, and morphological characteristics of a novel five‐layer hybrid composite. The system utilizes a symmetrical Jute/JUCO/Glass/JUCO/Jute stacking sequence reinforced with an epoxy matrix and synergistically enhanced by copper oxide (CuO) and titanium dioxide (TiO 2 ) microparticles. Fabricated via hand layup, the composites were evaluated at filler loadings of 1, 2, and 3 wt%. Results indicate that CuO at 3 wt.% yielded up to approximately 63.68% increase in tensile strength as compared to the control sample, while TiO 2 reached peak flexural strength and modulus at 42.15 MPa and 2.4 GPa, respectively. Impact strength trends suggest an increase of 121% with CuO and 85.25% with TiO 2 . Physical testing revealed that porosity and water absorption were reduced when microparticles were added, with TiO 2 providing better moisture resistance, as determined by the water absorption test. Improved fiber‐matrix interfacial adhesion was found in both micro‐filler systems by scanning electron microscopy analysis. These findings indicate that microfiller incorporation can enhance selected mechanical and physical properties of hybrid natural fiber composites. Specifically, the TiO 2 ‐reinforced hybrid composite (T‐3) demonstrated properties comparable to automotive interior components, suggesting potential for non‐structural or semi‐structural applications. However, the scope of the present study is limited to short‐term mechanical and physical evaluation, and additional investigations, particularly on fatigue performance, thermal stability, and long‐term environmental durability, are necessary to substantiate their suitability for demanding structural applications.