Durjoy Roy

Durjoy Roy

Auto-generated profile, based on publicly available information

Durjoy Roy

Department of Mechanical Engineering, Khulna University of Engineering & Technology, Khulna, Bangladesh

Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 May 2026 in SPE Polymers
Verified
Journal Article
Open access
NSNayan Sur
Nayan Sur
TNTitu Nath
Titu Nath
IZIshrak Ibn Zahid
Ishrak Ibn Zahid
ADArup Kumar Debnath
Arup Kumar Debnath
MHMd. Abdul Hasib
Md. Abdul Hasib
DRDurjoy Roy
Durjoy Roy
The development of sustainable, high‐performance materials has intensified the demand for natural fiber‐reinforced polymer (NFRP) composites. However, the inherent limitations of natural fibers, such as low interfacial bonding and high moisture absorption, necessitate advanced hybridization and filler modification. This study investigates the mechanical, physical, and morphological characteristics of a novel five‐layer hybrid composite. The system utilizes a symmetrical Jute/JUCO/Glass/JUCO/Jute stacking sequence reinforced with an epoxy matrix and synergistically enhanced by copper oxide (CuO) and titanium dioxide (TiO 2 ) microparticles. Fabricated via hand layup, the composites were evaluated at filler loadings of 1, 2, and 3 wt%. Results indicate that CuO at 3 wt.% yielded up to approximately 63.68% increase in tensile strength as compared to the control sample, while TiO 2 reached peak flexural strength and modulus at 42.15 MPa and 2.4 GPa, respectively. Impact strength trends suggest an increase of 121% with CuO and 85.25% with TiO 2 . Physical testing revealed that porosity and water absorption were reduced when microparticles were added, with TiO 2 providing better moisture resistance, as determined by the water absorption test. Improved fiber‐matrix interfacial adhesion was found in both micro‐filler systems by scanning electron microscopy analysis. These findings indicate that microfiller incorporation can enhance selected mechanical and physical properties of hybrid natural fiber composites. Specifically, the TiO 2 ‐reinforced hybrid composite (T‐3) demonstrated properties comparable to automotive interior components, suggesting potential for non‐structural or semi‐structural applications. However, the scope of the present study is limited to short‐term mechanical and physical evaluation, and additional investigations, particularly on fatigue performance, thermal stability, and long‐term environmental durability, are necessary to substantiate their suitability for demanding structural applications.

12 August 2026 in Scientific Reports
Verified
Journal Article
Open access
PDF file
DRDurjoy Roy
Durjoy Roy
DRDhrubo Roy
Dhrubo Roy
TNTitu Nath
Titu Nath
ADArup Kumar Debnath
Arup Kumar Debnath
MHMd. Abdul Hasib
Md. Abdul Hasib
This study explores the effect of silicon carbide (SiC) nanoparticles on both the mechanical and physical characteristics of aluminum-laminated hybrid composites reinforced with basalt and nylon fibers, representing a previously unexplored basalt-nylon hybrid fiber metal laminate system modified with SiC nanoparticles. The composites were made through a hand lay-up process, followed by compression molding and surface lamination with chemically treated aluminum sheets. SiC particles were incorporated at 0, 3, and 5 wt% to optimize the mechanical and physical attributes and to evaluate their influence on tensile strength, flexural strength, impact resistance, and water absorption behavior. The results show that only the highest tensile properties were achieved with 5 wt% SiC (SiC5), but other properties declined. However, 3 wt% SiC (SiC3) provided the best overall performance. Specifically, the tensile strength showed an increase from 117.71 MPa for the control sample (CS) to 121.19 MPa for SiC3, corresponding to an improvement of approximately 3%. In contrast, the flexural strength increased by about 5% in SiC3 and achieved a maximum flexural strength of 173.85 MPa compared to the control sample (CS). Moreover, the tensile and flexural moduli improved significantly by 159% and 46%, respectively, over the unfilled control specimen. A moderate improvement in impact resistance was also observed. Additionally, water absorption decreased by nearly 16% relative to CS, which is likely due to the uniform dispersion of SiC nanoparticles and the resulting improvement in barrier properties. However, a rise in SiC content to 5 wt% caused a decline in flexural strength, impact resistance, and moisture resistance, although the highest tensile strength of 122.3 MPa was achieved at this loading, likely due to particle agglomeration as well as void formation, as confirmed by SEM analysis.