16 October 2017 in Wood Material Science & Engineering
Timber buildings are increasing in their dimensions. Structural robustness is imperative for all buildings and specifically important for tall buildings. Lives can be saved if disproportionate collapse can be avoided after a catastrophic event (e.g. accident, terrorism). The literature about robustness is comprehensive concerning concrete and steel buildings, but is rather limited regarding timber. This paper reviews robustness in general and robustness of timber buildings in particular. Robustness is an intrinsic structural property, enhancing global tolerance to local failures, regardless of the cause. A deterministic approach to assess robustness is to remove certain load-bearing elements from the structure and compare the consequences to given limits. Design methods for robustness may be direct by assessing effects of local failure, or indirect by following guidelines. For robust timber buildings, the connections are the key aspects. Usually, metal connectors may provide the required joint ductility. For robust light timber-frame construction, rim beams may be designed. For timber posts and beams and cross laminated timber, guidance regarding robustness is scarce, but in some aspects they seem to be similar to steel frames and precast concrete. Future research should assess the capacity of connections, and evaluate the adequacy of seismic connectors for robust timber buildings.
3 February 2017 in The International Journal of Advanced Manufacturing Technology
9 August 2017 in Advances in Applied Ceramics: Structural, Functional and Bioceramics
This research focuses on the cutting performance of Al2O3 and Si3N4 ceramic cutting tools in up-milling plywood, the results of which are as follows. First, whether the tool material is Al2O3 or Si3N4 ceramic, the cutting forces at low-speed cutting were less than those at high-speed cutting, and the machining quality at low-speed cutting was greater than that at high-speed cutting. Then, whether at low- or high-speed cutting, the cutting forces of Al2O3 cutting tools were higher than those of Si3N4 cutting tools, and the machining quality of plywood milled by Al2O3 ceramic cutting tools was poorer than that milled by Si3N4 ceramic cutting tools. Finally, Si3N4 ceramic cutting tools were more suitable to machine the wooden productions with much glue content than Al2O3 ceramic cutting tools for the better machined quality.
13 April 2012 in Wood Material Science & Engineering
The aim of the study was to evaluate the main cutting force for two species of tropical Mozambican wood and to develop predictive models. Cutting these hardwoods is difficult. Determination of cutting parameters is required to optimize cutting processes, machines and tools in the cutting operations. This determination would enable the forestry and wood sector to achieve higher financial results. Samples of a lesser-known wood species Pseudolachnostylis maprounaefolia (ntholo) and a well-known wood species Swartzia madagascariensis (ironwood) were machined in a test apparatus. A standard single saw tooth mounted on a piezoelectric load cell was used to evaluate the main cutting force. Data were captured using an A/D converter integrated with National Instruments LabVIEW software. The measured signals were recorded at a sampling frequency of 25 kHz. The experimental set-up used response surface methodology for developing predictive models. The experimental clearly determined the relationship between the main cutting force and edge radius, wood density, rake angle, chip thickness, moisture content (MC) and cutting direction (CD). Among the studied variables, chip thickness and CD had the highest effect on the main cutting force level while wood density, MC and rake angle had the lowest effect.
5 August 2014 in Wood Material Science & Engineering
Most of the cracks are caused by changes in temperature and relative humidity which lead to shrinkage and swelling of the wood and thereby induce stresses in the structure. How these cracks influence the strength of the wooden structure, especially the shear strength, is not well understood. However, it is reasonable to expect that cracks have an impact on the shear strength as they preferably run along the beams in the direction of grain and bond lines. The purpose of this study was to investigate the load-bearing capacity of cracked glulam beams and to find a model that could predict the failure load of the beams due to the cracks. Three-point bending tests were used on glulam beams of different sizes with pre-manufactured cracks. An orthotropic elastic model and extended finite element method was used to model the behaviour of the cracked beams and to estimate the load-bearing capacity. The conclusions were validated by numerical simulations of the mechanical behaviour of three-point bending of glulam beams with different crack locations. The crack initiation load was recorded as the failure load and compared to the experimental failure load. The results of the compaction simulations agree well with the experimental results.
14 January 2019 in Journal of Mechanical Science and Technology