24 April 2017 in IEEE Microwave and Wireless Components Letters
In this letter, a planar differential-mode (DM) four-port circuit is proposed to design a balanced-to-balanced bandpass filter (BPF) with common-mode noise absorption add-on feature. By using the matrix transformation between the mixed and the single-ended scattering parameters, even- (odd-) mode equivalent circuit and the closed-form solutions of the proposed circuit structure are obtained based on the constraint rules. Finally, a microstrip DM BPF is designed and fabricated. The measured (simulated) results show that the relative bandwidth is 55.5% (57.5%) under the conditions of |SddBA| > -1 dB and |SddAA|, |SccAA|, and |SccBA| < -10 dB. Good agreements between the simulated and measured results verify the correctness of the design theory.
3 April 2017 in IEEE Transactions on Microwave Theory and Techniques
In this paper, a novel planar compact coupled-line circuit is proposed to design a single-ended-to-balanced power divider (PD) that can be used in numerous balanced circuits and systems. By using the matrix transformation between the mixed-mode (MM) scattering parameters and the single-ended scattering parameters, the constraint rules are deduced to realize the performance of equal power division with in-phase, good input (output) port matching, high isolation between two balanced outputs, high suppression of the common-mode (CM) noise, as well as the mode-conversion suppression between differential-mode signals and CM noise. Then, the closed-form design equations are derived using the even- and odd-mode analysis. Finally, a microstrip PD, which works at 1 GHz, is designed and fabricated. The measured (simulated) operating relative bandwidth is 37% (38%) from 0.76 (0.83 GHz) to 1.13 GHz (1.21 GHz). The consistency between the simulated and measured MM scattering parameters verifies the correctness of the design theory.
12 December 2017 in IEEE Transactions on Microwave Theory and Techniques
For the first time, the 6-port quadrature and rat-race couplers with balanced-unbalanced-hybrid ports are proposed. The corresponding design methodology is presented, which is capable of designing the proposed couplers with arbitrary power divisions and terminated resistances. In this paper, four types including quadrature and rat-race couplers are fully analyzed, covering all the application configurations of the balanced/unbalanced ports. Besides, the design equations are rigorously derived, with the final design procedures presented. Eventually, prototypes of the four coupler types are fabricated and experimentally measured. The final results sufficiently validate the proposed methodology.
22 December 2020 in IEEE Access
This paper presents a new design methodology for broadband Doherty architecture using the three-port input and output networks technique. The proposed topology was developed to overcome the Doherty power amplifier (DPA) bandwidth limitations. The output three-port network performs the impedance matching from any load impedance to the optimum loads for both main and peaking transistors and also combines the power delivered from the two devices at any power ratio. On the other hand, the input-splitting network is proposed for matching the input impedances of the two transistors to the source impedance. The freedom in choosing the power division ratio of the input network enables us to achieve a tradeoff between efficiency and linearity. Also, it provides a way to accomplish the phase compensation using an arbitrary phase difference between the two branches of the Doherty power amplifier and thus, helps obviate the need of the highly bandwidth limiting offset lines found in the Doherty design. A two-stage broadband Doherty power amplifier is implemented using 0.25-um GaN HEMT MMIC process to validate the proposed topology. The fabricated DPA was measured under both continuous wave (CW) and modulated signal at different operating frequencies. Across 3.3–3.7 GHz, the implemented DPA delivers a maximum output power exceeding 42 dBm, power added efficiency (PAE) over 52 % at the peak power and over 38 % in the back-off state over the operating 400 MHz bandwidth. The fully integrated circuit has a chip-size of 4.4 mm $\times\,\,3.5$ mm.
21 February 2017 in IEEE Microwave and Wireless Components Letters
A planar asymmetrical miniaturized circuit based on composite left- and right-handed transmission lines (CLRHTLs) is proposed to design a new balanced-to-single-ended (BTSE) power divider (PD) in this letter. The CLRHTLs are used to realize circuit miniaturization and positive-phase response. Conversion between the mixed-mode scattering parameters and the standard scattering parameters, and circuit analytical methods are discussed to realize the equal power division in phase from one differential input to two SE outputs. To verify the correctness of the proposed theory, a practical BTSE PD, which operates at 0.95 GHz, is designed and fabricated. The measured relative bandwidth is 26.3%, and the final circuit size is only $0.021~\lambda _{g}^{2}$ .
1 November 2015 in IET Microwaves, Antennas & Propagation
A planar microstrip circuit is proposed to design a kind of coupled‐line balun with good ports matching and high output‐ports isolation for complex source to complex load impedance transformation. This balun prototype essentially consists of three coupled‐line sections, a tapped open transmission‐line stub (TOTS) on the left‐hand side, and a tapped complex equivalent‐impedance part (TCEP) on the right‐hand side. The TCEP is the key to realise high output isolation and all ports matching. Based on the traditional even‐odd mode technique and the transmission‐line theory, closed‐form mathematical equations for circuit electrical parameters are obtained. To demonstrate this proposed design theory, a practical microstrip coupled‐line balun is designed, simulated and measured to operate at approximately 2 GHz, indicating high isolation and balanced output. Good agreements between the simulated and measured results verify this design.