Jérôme Billoué

Jérôme Billoué

Auto-generated profile, based on publicly available information

Jérôme Billoué

GREMAN UMR 7347, Université de Tours, CNRS, INSA-CVL 1 , 16 rue Pierre et Marie Curie, 37071 Tours

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 September 2012 in Discover Nano
Verified
Journal Article
Open access
PDF file
MCMarie Capelle
Marie Capelle
JBJérôme Billoué
Jérôme Billoué
PPPatrick Poveda
Patrick Poveda
GGGaël Gautier
Gaël Gautier
To study the influence of localized porous silicon regions on radiofrequency performances of passive devices, inductors were integrated on localized porous silicon regions, full porous silicon sheet, bulk silicon and glass substrates. In this work, a novel strong, resistant fluoropolymer mask is introduced to localize the porous silicon on the silicon wafer. Then, the quality factors and resonant frequencies obtained with the different substrates are presented. A first comparison is done between the performances of inductors integrated on same-thickness localized and full porous silicon sheet layers. The effect of the silicon regions in the decrease of performances of localized porous silicon is discussed. Then, the study shows that the localized porous silicon substrate significantly reduces losses in comparison with high-resistivity silicon or highly doped silicon bulks. These results are promising for the integration of both passive and active devices on the same silicon/porous silicon hybrid substrate.

3 July 2012 in Discover Nano
Verified
Journal Article
Open access
PDF file
GGGael Gautier
Gael Gautier
FCFrederic Cayrel
Frederic Cayrel
MCMarie Capelle
Marie Capelle
JBJérome Billoué
Jérome Billoué
XSXi Song
Xi Song
JMJean-François Michaud
Jean-François Michaud
In this paper, we study the electrochemical anodization of n-type heavily doped 4 H-SiC wafers in a HF-based electrolyte without any UV light assistance. We present, in particular, the differences observed between the etching of Si and C faces. In the case of the Si face, the resulting material is mesoporous (diameters in the range of 5 to 50 nm) with an increase of the ‘chevron shaped’ pore density with depth. In the case of the C face, a columnar morphology is observed, and the etch rate is twice greater than for the one for the Si face. We've also observed the evolution of the potential for a fixed applied current density. Finally, some wafer defects induced by polishing are clearly revealed at the sample surfaces even for very short etching times.

17 March 2011 in Physica Status Solidi (a)
Verified
Journal Article
Closed access
PDF file
JBJérôme Billoué
Jérôme Billoué
GGGaël Gautier
Gaël Gautier
LVLaurent Ventura
Laurent Ventura

2 February 2018 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
RARozenn Allanic
Rozenn Allanic
DBDenis Le Berre
Denis Le Berre
YQYves Quere
Yves Quere
CQCédric Quendo
Cédric Quendo
DCDavid Chouteau
David Chouteau
JBJerome Billoue
Jerome Billoue
This letter addresses a discrete tunable resonator with three different states controlled by a single dc source. The passive components are designed together with the active elements, and both are integrated into a silicon substrate. This method of codesign offers great flexibility in doped area sizing and positioning, allowing for easy management of novel three-state resonators based on two different doped areas (or two different surfaces of semiconductor junctions). The largest area switches from the reverse state (OFF state) to the forward state (ON1 state), with a lower bias voltage than that of the smallest area (ON2 state). This concept offers some new degrees of freedom in the design of tunable microwave devices, showcased in this letter by a demonstrator that can operate at three different resonant frequencies. Good agreement was obtained between simulations and measurements in the three states. Insertion losses are lower than 1.6 dB and the same for the different states.

11 October 2012 in Discover Nano
Verified
Journal Article
Open access
PDF file
SMSamuel Menard
Samuel Menard
AFAngélique Fèvre
Angélique Fèvre
DVDamien Valente
Damien Valente
JBJérôme Billoué
Jérôme Billoué
GGGaël Gautier
Gaël Gautier
We present in this paper a novel application of porous silicon (PS) for low-power alternating current (AC) switches such as triode alternating current devices (TRIACs) frequently used to control small appliances (fridge, vacuum cleaner, washing machine, coffee makers, etc.). More precisely, it seems possible to benefit from the PS electrical insulation properties to ensure the OFF state of the device. Based on the technological aspects of the most commonly used AC switch peripheries physically responsible of the TRIAC blocking performances (leakage current and breakdown voltage), we suggest to isolate upper and lower junctions through the addition of a PS layer anodically etched from existing AC switch diffusion profiles. Then, we comment the voltage capability of practical samples emanating from the proposed architecture. Thanks to the characterization results of simple Al-PS-Si(P) structures, the experimental observations are interpreted, thus opening new outlooks in the field of AC switch peripheries.

9 July 2012 in Discover Nano
Verified
Journal Article
Open access
PDF file
TDThomas Defforge
Thomas Defforge
JBJérôme Billoué
Jérôme Billoué
MDMarianne Diatta
Marianne Diatta
FVFrançois Tran Van
François Tran Van
GGGaël Gautier
Gaël Gautier
In this article, the physico-chemical and electrochemical conditions of through-silicon via formation were studied. First, macropore arrays were etched through a low doped n-type silicon wafer by anodization under illumination into a hydrofluoric acid-based electrolyte. After electrochemical etching, ‘almost’ through-silicon macropores were locally opened by a backside photolithographic process followed by anisotropic etching. The 450 × 450-μm² opened areas were then selectively filled with copper by a potentiostatic electrochemical deposition. Using this process, high density conductive via (4.5 × 105 cm−²) was carried out. The conductive paths were then electrically characterized, and a resistance equal to 32 mΩ/copper-filled macropore was determined.