In this paper, organic-inorganic hybrid perovskite CH3NH3PbI3 based heterostructure photodetector is fabricated on fluorine doped tin oxide (FTO) substrate. The perovskite CH3NH3PbI3 and metal oxide ZnO are synthesized using the sol-gel chemical route. The synthesized hybrid perovskite CH3NH3PbI3 has a tetragonal phase with a crystallite size of ~39.01 nm, whereas ZnO has a wurtzite hexagonal structure with a crystallite size of ~26.47 nm. The uniform distribution of particles is found in the thin film of CH3NH3PbI3 and ZnO with an average particle size of ~50 nm and ~30 nm, respectively. An efficient photoluminescence band is observed at ~1.59 eV in CH3NH3PbI3 thin film measured at ambient condition and excited with light of wavelength 405 nm. The heterostructure is formed between perovskite and ZnO which also work as an efficient electron transport layer. The heterostructure is characterized using I-V and C-V measurements which confirm the formation of barrier between CH3NH3PbI3 and ZnO. The photoresponsivity of ~21.8 A/W is obtained at an applied bias voltage of -1 V under illumination of light obtained from monochromator of wavelength ~436 nm and intensity ~190 &LW/cm2.
Titanium dioxide (TiO2) based capacitive sensor for the detection of hydrogen gas (H2) at room temperature is reported in this article. The metal-oxide-semiconductor (MOS) structure is fabricated on a silicon substrate with electron beam evaporated TiO2 oxide and thermally evaporated palladium (Pd) metal. The surface morphology of Pd and TiO2 films are investigated by atomic force microscopy (AFM) and scanning electron microscopy (SEM). The porous Pd film is found, which is responsible for enhanced adsorption of H2. The response of MOS sensor for H2 gas is measured in the form of a shift in capacitance-voltage (C-V) and conductance-voltage (G-V) characteristics. The maximum sensitivities for 4% H2 gas are found as 84% and 90% in ambient air and nitrogen gas, respectively. The fabricated Pd/TiO2/Si MOS sensor shows fast response and recovery for H2 gas. The selectivity of the MOS sensor with most interfering organic vapours such acetone, chloroform, ethanol, isopropanol, and methanol are also investigated.
30 September 2019 in IEEE Journal of Photovoltaics
The efficiency improvement of perovskite solar cells (PSCs) by solvothermal etching and/or TiCl $_4$ treatment of TiO $_2$ nanorod arrays (NRAs) based electron transport layer (ETL) is reported in this article. The TiO $_2$ NRAs are explore for the ETL because of their better direct carrier transportation over other TiO $_2$ nanostructures. The solvothermal etching of TiO $_2$ NRAs enhances the surface-to-volume ratio of the ETL, which, in turn, enhances the power conversion efficiency (PCE) of the PSCs. All the measurements are performed at room temperature and high humid (with ∼65% humidity) conditions to demonstrate the performance of the PSCs under normal environmental conditions. A noteworthy efficiency of 15.16% with an improved fill factor and short circuit current density (J $_\text{SC}$ ) is achieved in the proposed PSCs under this article. The performance of the PSC is shown to improve further by exploring TiCl $_4$ treatment of the solvothermally etched TiO $_2$ NRs as the ETL in the device.
A poly (3, 3“’- dialkylquaterthiophene) (PQT-12) based flexible metal-semiconductor-metal (MSM) nitrogen dioxide (NO$_{2}$) gas sensor fabricated on a flexible polyamide substrate has been reported in this paper for the first time. The thin PQT-12 film deposited on the polyamide substrate is investigated by X-ray diffraction, atomic force microscopy, and scanning electron microscopy. The sensor shows a gas response of ~24% with a response time of ~41 seconds at a very low concentration of 100 ppb NO$_{2}$ gas under ambient air atmosphere. The gas response of ~48% is measured at higher concentration of 500 ppb NO$_{2}$ gas. The NO$_{2}$ gas detection has been illustrated using a prototype circuit for the proposed sensor.
In this paper the inductive degenerated Differential Low Noise Amplifier (DLNA) is designed with operating frequency 2.4 GHz using 0.18 μm CMOS Technology. The DLNA is biased at 1.8 V supply and perfectly matched with input impedance of 50 Ω. Designed DLNA provides power gain of 21.59 dB with a noise figure of 398.1 mdB.