Multi-walled carbon nanotubes (MWCNTs) are an alternative for storage with low cost, eco-friendly, and good performance for both process adsorption and desorption. Herein, a purification procedure of MWCNTs was successfully described and studied by using XRD, TEM, Raman spectroscopy and by means of N2 adsorption-desorption isotherms using the BET method. The H2 storage properties at room temperature of the purified carbon nanotubes exposed to gas under pressures between 0.39 and 13.33 kPa was investigated by using the quartz crystal microbalance technique. It was found that the H2 adsorption capacity is strongly dependent on the morphological and structural characteristics of the carbon nanotubes and their specific surface area. The best sample with specific surface area of 729.4 ± 3 m2 g−1 shows a maximum adsorption capacity of 3.46 wt% at 12.79 kPa of H2 exposure pressure. The adsorption kinetics (t95%) from the different purified MWCNTs was also investigated as a function of the H2 exposure pressure as well as the performance of these MWCNTs on the reversibility of the H2 loading/unloading process when underwent to successive cycles of gas exposure.
Herein, we report a series of carbonized titanium oxide composite (CTPs) electrode materials, synthesized via pyrolysis of polyaniline titanium isopropoxide precursors and engineered for high-performance, photocharging microsupercapacitor (MSC) device. Microstructural and chemical state analyses revealed the formation of a nanostructured nitrogen-doped graphitic carbon matrix embedded with semicrystalline anatase TiO2, exhibiting synergistic structural interactions and defect-induced photoactivity. Among the series, the optimum CTP sample demonstrated the most favorable optoelectronic and electrochemical characteristics, with a moderate optical bandgap (~3.55 eV), strong UV absorption and light-matter interactions, and high specific capacitance (456 F g-1 at 1 mA cm-2). A laser-induced interdigitated MSC prototype device based on optimum CTP was fabricated and evaluated under both dark and UV-illuminated conditions. Cyclic voltammetry and galvanostatic charge-discharge analyses revealed enhanced areal capacitance from 3.81 mF cm-2 (dark) to 5.92 mF cm-2 (12.5 mW cm-2 UV), alongside improved energy density (0.72 μWh cm-2), and long discharge durations. Electrochemical impedance spectroscopy confirmed reduced series resistance and steeper Warburg slopes under illumination. Mott–Schottky analysis further evidenced increased donor density and a negative shift in flat-band potential with increasing UV intensity. The results unveiled the CTP microsupercapacitor’s viability as a light-tunable, photo-rechargeable energy storage platform for self-powered microelectronics devices.
In the present study, the effect of injected O2 pressure to a hydrothermal reactor on the growth, morphology, structure and hydrogen adsorption properties of CuO hierarchical microstructures was investigated. The synthesis consisted of a simple one-step hydrothermal reaction using copper chloride and aqueous ammonia. Hydrothermal reactions were carried at 200 °C at reaction times of 1 and 12 h injecting at the beginning of the synthesis O2 pressures of 0, 30 or 60 bar. The samples were characterized by SEM and EDS for morphological and chemical information, XRD for determination of crystalline phases, lattice parameters and crystallinity grade using Rietveld refinement. Specific surface area was determined using BET method from nitrogen adsorption/desorption isotherm measurements. Hydrogen adsorption capacities at 20 °C were studied for key samples using the quartz crystal microbalance technique under gas exposure pressures between 3 and 100 Torr. It was found that the samples were of monoclinic CuO phase consisting mainly of sphere-like hierarchical microstructures of different average sizes assembled by sheets. The effect of the reactor pressure was mainly seen on average size of the CuO microstructures due to changes in the growth rate, specifically during the first stages of the hydrothermal reaction. Reactor pressure induced changes on the crystallinity of the samples were determined but no correlation was stated. Hydrogen adsorption capacities of studied samples measured at 100 Torr ranged from 0.27 to 0.6 wt%, indicating a good performance as compared with other reported values. Oxygen deficiency in CuO can influence on the hydrogen adsorption capacity.