Marvin Wenzel

Marvin Wenzel

Auto-generated profile, based on publicly available information

Marvin Wenzel

Institute of High-Frequency Technology, Hamburg University of Technology, Hamburg, Germany

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 February 2023 in IEEE Microwave Magazine
Verified
Journal Article
Closed access
MWMarvin Wenzel
Marvin Wenzel
NANils C. Albrecht
Nils C. Albrecht
DLDominik Langer
Dominik Langer
MHMarkus Heyder
Markus Heyder
AKAlexander Kölpin
Alexander Kölpin
Vital signs are most essential in medical care to evaluate a patient’s health situation. Today, electronic devices reliably measure the most important vital signs: heartbeat and respiration. Electrocardiography (ECG) measures the electrophysiological heart activity, while breathing can be detected with impedance pneumography (IP), which evaluates the periodic change of thorax impedance as we breathe in and out. While continuous monitoring of vital signs provides valuable medical information that can improve diagnostics, enable adaptive therapy, and generate new medical knowledge, there are also disadvantages. Medical procedures like ECG or IP require cables and electrodes, thus considerably reducing a patient’s mobility. Furthermore, electrodes cause skin irritation if applied too long, which often limits the continuous monitoring of vital signs to situations of absolute medical necessity.

1 November 2024 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
BTBartosz Tegowski
Bartosz Tegowski
DLDominik Langer
Dominik Langer
MWMarvin Wenzel
Marvin Wenzel
NANils C. Albrecht
Nils C. Albrecht
AKAlexander Kölpin
Alexander Kölpin
In the context of radar, this article examines phenomena that occur in conditions where the physical extent of the target cannot be considered negligible compared to the range and, thus, far-field assumptions are violated. Based on physical optics principles, a transfer function of the radar channel between the antenna input and output power wave is derived for a monostatic configuration. The effects are studied using a circular metallic disk as an exemplary target. Exact and approximative expressions for the transfer function are derived incorporating the influence of the antenna radiation characteristic in addition. Measurements with targets of different sizes performed with horn as well as open-ended waveguide antennas at 24 and 61 GHz validate the phenomena of receive power level fading and nonlinear phase distortion.

17 March 2023 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
BTBartosz Tegowski
Bartosz Tegowski
MWMarvin Wenzel
Marvin Wenzel
AKAlexander Kölpin
Alexander Kölpin
This article presents a novel technique to determine the antenna phase center. It relies on measuring the direction of arrival of the radiated field. Therefore, no access of the measurement equipment to the antenna under test is required. A direction-of-arrival detector is implemented that performs phase difference measurements in two orthogonal planes. Six-port interferometers are used for this purpose. By considering phase differences, the proposed method is robust against phase disturbances, which may occur at the feed of the antenna under test, e.g., due to flexible cables or rotary joints. Besides, impairments stemming from reflections in the measurement environment are addressed. Measurements of a K-band horn and a patch antenna in an anechoic chamber validate the approach. A single phase center is determined for each principle plane as well as for the three-dimensional main beam. In addition, the phase center locus is retrieved.

8 May 2024 in IEEE Microwave Magazine
Verified
Journal Article
Closed access
BTBartosz Tegowski
Bartosz Tegowski
DLDominik Langer
Dominik Langer
ASAnton Sieganschin
Anton Sieganschin
MWMarvin Wenzel
Marvin Wenzel
AKAlexander Kölpin
Alexander Kölpin
The advance of 3D-printing technology over the last decade makes additive manufacturing not only attractive for rapid prototyping, but also provides it as a trendsetting approach to realize conventional as well as sophisticated functional microwave and millimeter-wave passive components. It has proven its ability to replicate conventional waveguides with a comparable electrical performance [1] . In this way, low-cost, lightweight waveguides with customized dimensions and shapes are realizable. Moreover, 3D printing enables the implementation of unconventional complex-shaped waveguide components, such as filters [2] , [3] , interconnects, or antennas [4] , whose design is restricted by the engineer’s creativity rather than by limitations of conventional fabrication techniques.