7 December 2020 in IEEE Transactions on Microwave Theory and Techniques
This work presents diplexers realized with folded circular substrate integrated waveguide (FCSIW) cavity filters. The properties of such cavities are analyzed, and empirical equations for calculating the resonant frequencies are given. The analysis relies on an even-/odd-mode decomposition. A 10-GHz filter is designed based on this approach. In the second step, its size is reduced, still maintaining the passband behavior. An asymmetric taper is used to connect two such filters to realize a diplexer. Two diplexers with center frequencies of 10/15 and 12/13.5 GHz are presented. The diplexers are several times more compact than comparable devices reported in the literature. The components are manufactured, and the functionality is demonstrated by simulation and measurements.
9 March 2021 in IEEE Microwave and Wireless Components Letters
This contribution presents a vertical transition between a WR34 rectangular waveguide (RWG) and two grounded coplanar waveguides (GCPW). It is intended for dual-band phased array applications and thus includes a diplexer. The RWG is the common port and the GCPWs are the diplexed 20 and 30 GHz ports. This yields a very compact design compared to conventional cascaded circuit topologies. The realized component exhibits a port matching and an isolation exceeding 10 dB and 30 dB, respectively, over more than 500 MHz in both bands.
5 May 2023 in International Journal of Microwave and Wireless Technologies
This contribution presents miniaturization techniques for folded circular substrate integrated waveguide (FCSIW) cavity filters. The cavities support dual-mode operation. Two of these cavities are combined to form a fourth-order filter. Two filter designs are implemented. The first one serves as a reference and exhibits good manufacturability. For the second one, the cavity is modified, which leads to $50\%$ more compactness. The designs are experimentally verified with 10 GHz bandpass filters. Even though the achieved level of compactness requires higher technological effort, the measurements validate the miniaturization concept. The out-of-band rejection exceeds 40 dB between 11.2 and 30 GHz for the reference filter and between 11.3 and 33 GHz for the miniaturized one. The implemented components are compared with state-of-the-art filters.
26 September 2022 in IEEE Transactions on Microwave Theory and Techniques
This work proposes a transmission line approach to determine the surface impedance of conductors with rough surfaces. Based on the gradient model, the roughness is represented by a gradual transition of the intrinsic impedance. Discretization and successive impedance transformations then directly yield the surface impedance. Evaluating the fields is not necessary to this end, but still feasible if required. Investigations of the proposed model confirm the field diffusion to be fully characterized by a single dimensionless ratio, which enables a comprehensive analysis of the surface impedance regarding its dependency on frequency, conductivity, and roughness.
29 March 2021 in International Journal of Microwave and Wireless Technologies
This contribution deals with a frontend for interleaved receive (Rx)-/transmit (Tx)-integrated phased arrays at K-/Ka-band. The circuit is realized in printed circuit board technology and feeds dual-band Rx/Tx- and single-band Tx-antenna elements. The dual-band element feed is composed of a substrate-integrated waveguide (SIW) diplexer with low insertion loss, a low-noise amplifier (LNA), a bandpass filter, and several passive transitions. The compression properties of the LNA are identified through two-tone measurements. The results dictate the maximum allowable output power of the power amplifier. The single band feed consists of a SIW with several transitions. Simulation and measurement results of the individual components are presented. The frontend is assembled and measured. It exhibits an Rx noise figure of 2 dB, a Tx insertion loss of ~ 2.9 dB, and an Rx/Tx-isolation of 70 dB. The setup represents the unit cell of a full array and thus complies with the required half-wave spacing at both Rx and Tx.
8 May 2024 in IEEE Microwave Magazine
The advance of 3D-printing technology over the last decade makes additive manufacturing not only attractive for rapid prototyping, but also provides it as a trendsetting approach to realize conventional as well as sophisticated functional microwave and millimeter-wave passive components. It has proven its ability to replicate conventional waveguides with a comparable electrical performance [1] . In this way, low-cost, lightweight waveguides with customized dimensions and shapes are realizable. Moreover, 3D printing enables the implementation of unconventional complex-shaped waveguide components, such as filters [2] , [3] , interconnects, or antennas [4] , whose design is restricted by the engineer’s creativity rather than by limitations of conventional fabrication techniques.