17 July 2024 in Physical Review Applied
Controlled engineering of vortex pinning sites in copper-oxide superconductors is a critical issue in manufacturing devices based on magnetic flux quanta. To address this, we employed a focused -ion beam (-FIB) to irradiate thin films and create ultradense hexagonal arrays of defects with lattice spacings as small as 20 nm. Critical current and magnetoresistance measurements demonstrate efficient pinning by a matching field of 6 T visible in a huge temperature range from the critical temperature down to 2 K. These results show that -FIB irradiation provides excellent opportunities for the development and application of superconducting fluxonic devices based on Abrikosov vortices. In particular, our findings suggest that such devices can operate at temperatures far below , where superconductivity is robust.
22 July 2025 in Physical Review Applied
12 December 2024 in IEEE Transactions on Applied Superconductivity
The development of a fabrication process for Josephson junctions (JJs) using a direct-write helium-focused ion beam (He-FIB) technique provides the opportunity to control parameters such as the critical current $I_{\mathrm{c}}$ and normal-state resistance $R_{\mathrm{n}}$ of individual JJs in YBa$_{2}$Cu$_{3}$O$_{7-\mathrm{x}}$ JJ arrays. Such arrays could be used as a voltage calibration standard that is operated at higher temperatures and higher driving frequencies than the currently used niobium JJ arrays. This study presents the fabrication process of 79 YBa$_{2}$Cu$_{3}$O$_{7-\mathrm{x}}$ JJs in a meander array design using a direct writing He-FIB process with the same irradiation dose for all JJs. In this design, each of the JJs can be measured individually, and adjacent JJs that exhibit similar and suitable parameters for a voltage standard array can be measured in series. The scattering of the JJ parameters was investigated at 5 K and resulted in a spread in $I_{\mathrm{c}}$ of about 60% and in $R_{\mathrm{n}}$ of 25%. However, a couple of subarrays with a spread lower than 10% could be found. In addition, these JJ subarrays were irradiated with high-frequency radiation in the GHz and THz range at a temperature of 20 K and synchronization of up to three JJs was observed in both frequency ranges.
12 January 2024 in IEEE Transactions on Applied Superconductivity
Josephson junctions with customizable parameters, including critical current $I$ c and normal state resistance $R$ n , hold great promise across a wide range of applications. Notably, high-temperature superconductors like YBa 2 Cu 3 O 7-x have been interesting since their discovery due to their simplified cooling requirements. YBa 2 Cu 3 O 7-x Josephson junctions can operate within the terahertz (THz) frequency range, rendering them highly suitable for various applications. To maximize their suitability at these high frequencies, it is imperative to precisely determine their THz parameters. Helium focused ion beam (He-FIB) technology is a very promising fabrication method for customizable Josephson junctions. It allows precise control of the He-FIB dose during the fabrication of Josephson junctions and facilitates the fine-tuning of I c and R n . This study presents the fabrication process of YBa 2 Cu 3 O 7-x Josephson junctions using He-FIB irradiation and explores the variations of parameters with dose, evaluating their suitability within the THz range. Also, the scattering of parameters of He-FIB Josephson junctions fabricated with the same He-FIB dose is investigated. Additionally, we examine the high-frequency properties of such junctions and scrutinize the associated Shapiro steps within the THz frequency spectrum. We observe an exponential relationship between I c and the He-FIB dose. Moreover, Shapiro steps emerge under the influence of radiation spanning from 40 GHz to as high as 1.4 THz.
5 September 2025 in Physical Review Applied
15 December 2025 in IEEE Transactions on Applied Superconductivity
Fabrication of YBa2Cu3O7-x Josephson junctions (JJs) using a direct-write helium-focused helium ion beam (He-FIB) technique has great potential for various applications due to tunable JJ parameters and arbitrary positioning. This technique allows placing multiple JJs in series to create JJ arrays. They could be used as a voltage standard that is operated at higher temperatures and driving frequencies than the currently used niobium-based JJ arrays. Small YBa2Cu3O7-x He-FIB JJ arrays with superposed Shapiro steps for up to three JJs have already been demonstrated. The number of JJs in the array was limited by the parameter spread of the individual JJs. This study presents WRspice simulations of JJ arrays, which indicate that the normal state resistance $R$n is the most crucial parameter to achieve flat Shapiro steps in JJ arrays. The idea of adding a shunt resistor to the JJ array to deal with the spread in $R$n values is investigated. A new design for GHz frequencies is presented, and the fabrication process is described. The properties of the shunt resistor are evaluated by van der Pauw measurements. Comparison of measurements with and without shunt resistor shows the desired effect of changing the total resistance of the JJ array while maintaining the critical current value. Finally, measurements of JJ arrays demonstrating superposed Shapiro steps at 20 k at GHz frequencies are presented.