Ashok Kumar Gupta

Ashok Kumar Gupta

Auto-generated profile, based on publicly available information

Ashok Kumar Gupta

VLSI Design Lab., Department of Electronics and Communications, Dr. B. R. Ambedkar National Institute of Technology, Jalandhar, India

Research Focus & Metrics

Academic Career Length

36Years (1991-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 July 2019 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
AGAshok Kumar Gupta
Ashok Kumar Gupta
ARAshish Raman
Ashish Raman
Naveen KumarNaveen Kumar
Naveen Kumar
A novel device architecture charge plasma-based Ring-TFET (CP-RingTFET) has been described in this work. The ring structure of the proposed device uses a core-shell architecture with a drain at the center covered with the channel and followed by the source. The ring structure has the advantage of ultrascaling and mechanical strength as compared to the nanowire structure. The performance characteristics of the Ring-TFET are much better as compared to nanowire-TFET with similar physical dimensions. To investigate the impact of charge plasma on RingTFET architecture, various analog and linearity parameters have been studied; such as off-state current (Ioff), on-state current (Ion), Ion/Ioff, subthreshold slope (SS), gate-to-gate capacitance, transconductance (gm), transconductance gain factor (TGF), threshold voltage (VTH), higher-order transconductances, higher-order harmonic distortions, third-order current intercept point (IIP3), third-order intermodulation distortions (IMD3), and higher-order voltage intercept points. The ability of the CP-RingTFET to enhance the performance of the proposed device is confirmed with the reduction of Ioff, improving Ion/Ioff, lower SS including the benefits of threshold voltage reduction.

1 February 2020
Verified
Conference Paper
Closed access
AGAshok Kumar Gupta
Ashok Kumar Gupta
ARAshish Raman
Ashish Raman
Naveen KumarNaveen Kumar
Naveen Kumar
RRRavi Ranjan
Ravi Ranjan
In this paper, a universal asynchronous receiver and transmitter (UART) are described, which is basically a serial data transmission protocol used in digital circuit applications. The architecture of the UART transmitter has a baud rate generator, parity generator, transmitter finite state machine (FSM) and parallel in serial out register (PISO). UART receiver has a baud rate generator, negative edge detector, parity checker, receiver finite state machine (FSM) and serial in parallel out (SIPO) register. The baud rate generator of both transmitter and receiver is the same, so the baud rate of transmitter/receiver is the same. Baud rate generator is the same as the frequency divider circuit. The data frame of the UART transmitter is 1 start bit, 8 transmits data bits, 1 parity bit and 1 stop bit. The baud rate of the transmitter and receiver is 4 Mbps using the system clock of 64 MHz’s. Implementation, simulation, and synthesis is done Xilinx Vivado 2016.2 version tool. The design is verified using simulated waveform and synthesized on the FPGA Zed board.

30 June 2020 in Applied Physics A
Verified
Journal Article
Closed access
PDF file
AGAshok Kumar Gupta
Ashok Kumar Gupta
ARAshish Raman
Ashish Raman


1 May 2002 in Organic Process Research & Development
Verified
Journal Article
Closed access
SCSou-Jen Chang
Sou-Jen Chang
DFDilinie Fernando
Dilinie Fernando
MFMichael Fickes
Michael Fickes
AGAshok K. Gupta
Ashok K. Gupta
DHDavid Richard Hill
David Richard Hill
SWSteven J. Wittenberger
Steven J. Wittenberger