13 October 2021 in JACS Au
The electrochemical reduction of CO2 is widely studied as a sustainable alternative for the production of fuels and chemicals. The electrolyte’s bulk pH and composition play an important role in the reaction activity and selectivity and can affect the extent of the buildup of pH gradients between the electrode surface and the bulk of the electrolyte. Quantifying the local pH and how it is affected by the solution species is desirable to gain a better understanding of the CO2 reduction reaction. Local pH measurements can be realized using Scanning Electrochemical Microscopy (SECM); however, finding a pH probe that is stable and selective under CO2 reduction reaction conditions is challenging. Here, we have used our recently developed voltammetric pH sensor to perform pH measurements in the diffusion layer during CO2 reduction using SECM, with high time resolution. Using a 4-hydroxylaminothiophenol (4-HATP)/4-nitrosothiophenol (4-NSTP) functionalized gold ultramicroelectrode, we compare the local pH developed above a gold substrate in an argon atmosphere, when only hydrogen evolution is taking place, to the pH developed in a CO2 atmosphere. The pH is monitored at a fixed distance from the surface, and the sample potential is varied in time. In argon, we observe a gradual increase of pH, while a plateau region is present in CO2 atmosphere due to the formation of HCO3– buffering the reaction interface. By analyzing the diffusion layer dynamics once the sample reaction is turned “off”, we gain insightful information on the time scale of the homogeneous reactions happening in solution and on the time required for the diffusion layer to fully recover to the initial bulk concentration of species. In order to account for the effect of the presence of the SECM tip on the measured pH, we performed finite element method simulations of the fluid and reaction dynamics. The results show the significant localized diffusion hindrance caused by the tip, so that in its absence, the pH values are more acidic than when the tip is present. Nonetheless, through the simulation, we can account for this effect and estimate the real local pH values across the diffusion layer.
28 August 2014 in Journal of Vacuum Science & Technology A
Tantalum oxide has shown promising electrical switching characteristics for memristor devices. Consequently, a number of reports have investigated the electrical behavior of TaOx thin films. Some effort has been made to characterize the composition of the TaOx films and it is known that there must be an optimal stoichiometry of TaOx where forming and switching behavior are optimized. However, many previous reports lack details on the methodology used for identifying the chemistry of the films. X-ray photoelectron spectroscopy has been the most commonly used technique; however, peak fitting routines vary widely among reports and a native surface oxide of Ta2O5 often confounds the analysis. In this report a series of large area TaOx films were deposited via sputtering with controlled O2 partial pressures in the sputtering gas, resulting in tunable oxide compositions. Spectra from numerous samples from each wafer spanning a range of oxide stoichiometries were used to develop a highly constrained peak fitting routine. This procedure allowed for the composition of the TaOx films to be identified with greater detail than elemental ratios alone. Additionally, the peak fitting routine was used to evaluate uniformity of deposition across individual wafers. The appearance of a greater contribution of Ta4+ oxidation states in the oxygen starved films are believed to relate to films with optimal forming characteristics.
5 April 2023 in Additive Manufacturing
3 September 2021 in Analytical Chemistry
Mass-transport-limited catalysis and membrane transport can be characterized by concentration profiles surrounding active surfaces. Scanning electrochemical microscopy (SECM) is a tool that has been used to measure concentration profiles; however, the presence and geometry of the tip can distort these profiles due to hindered diffusion, which in turn alters chemical behavior at the catalytic surface. To fully characterize the behavior of surface features such as catalytic sites, it is essential to account for and analytically remove the effect of tip presence. In this work, atomic force microscopy-based SECM (AFM-SECM) measurements over poly(tetrafluoroethylene) (PTFE) and gold electrode surfaces are used to measure negative and positive-feedback approach curves, respectively. By inversely fitting these approach curves with a finite element method (FEM) model, we derive kinetic and geometric tip parameters that characterize the effect of tip presence. Tip effects may be removed in the model to estimate concentration profiles and reaction properties for the case where no tip is present. A maximum 120% increase in the concentration at one tip radii above the surface is observed due to the presence of the tip, where the concentration field is compressed vertically, in proportion to surface feature size and tip separation. Conical AFM-SECM tips, with a higher ratio of tip height to the base size, introduce less concentration distortion than disk-shaped AFM-SECM tips.
1 June 2026 in Journal of the Electrochemical Society
Zirconium (Zr) possesses outstanding properties, including exceptional chemical resistance and a high melting point, and is therefore desirable for use in a wide variety of challenging environments, such as in nuclear reactors and the chemical processing industry. To minimize the amount of Zr required for any given application, developing methods for generating metallic Zr coatings is highly advantageous. Owing to Zr’s highly negative reduction potential, electrodeposition in traditional solvents at near ambient temperatures remains challenging and thus not well understood. Due to the extreme conditions required to deposit this metal, extensive work has been conducted in molten salt electrolytes, however the broad applicability of this methodology is limited due to its corrosivity. The primary focus of this article is to present an overview of Zr’s electrochemical behavior and to consolidate the efforts of researchers in exploring electrodeposition techniques for Zr involving aqueous, organic, ionic liquid, deep eutectic, and molten salt solvents. With this information, we highlight trends across solvent systems and opportunities for future research.