6 February 2018 in IEEE Electron Device Letters
ARAshwin Rishinaramangalam
We demonstrate a high-speed nonpolar m-plane InGaN/GaN micro-scale light-emitting diode (LED) with a record electrical -3dB modulation bandwidth of 1.5 GHz at a current density of 1 kA/cm2. A differential carrier lifetime (DLT) of 200 ps at 1 kA/cm2 was extracted using a rate-equation model. The short DLT is attributed to the high electron-hole wavefunction overlap in polarization-free nonpolar InGaN/GaN quantum wells, which leads to a higher spontaneous emission rate at low current densities compared to polar c-plane quantum wells. LEDs with improved high-speed performance at low current densities will help reduce power dissipation and increase efficiency in Gb/s visible-light communication systems.
27 December 2018 in Physica Status Solidi (a)
The performance of III‐nitride devices is degraded by polarization in a wurtzite crystal structure. Nonpolar and semipolar III‐nitrides have been extensively studied since the early 2000s as a solution to the polarization‐related issues. Removal of polarization is expected to improve the radiative efficiency, optical gain, charge transport, and potentially offer solutions to the challenging problems in III‐nitride light‐emitting diodes (LEDs) known as efficiency droop and the green gap. In addition, use of nonpolar and semipolar orientations is also predicted to offer polarization pinning in some devices due to anisotropic in‐plane strain. Despite the many potential advantages over c‐plane, nonpolar and semipolar optoelectronic devices have not successfully replaced conventional c‐plane devices in the commercial sector. Here, nonpolar and semipolar III‐nitrides are reviewed after more than a decade of development. The successes and challenges of nonpolar and semipolar orientations for applications such as LEDs, laser diodes, superluminescent diodes, and vertical‐cavity surface emitting lasers are discussed. New potential avenues for nonpolar and semipolar III‐nitrides are also highlighted, including visible‐light communication and power electronics. The availability of low‐cost, high‐crystal‐quality substrates with nonpolar or semipolar orientation is discussed and alternative approaches for realizing these orientations are presented, including selective‐area bottom‐up nanostructures.
22 January 2018 in Applied Physics Letters
ARA. K. Rishinaramangalam
+1
High-speed InGaN/GaN blue light-emitting diodes (LEDs) are needed for future gigabit-per-second visible-light communication systems. Large LED modulation bandwidths are typically achieved at high current densities, with reports close to 1 GHz bandwidth at current densities ranging from 5 to 10 kA/cm2. However, the internal quantum efficiency (IQE) of InGaN/GaN LEDs is quite low at high current densities due to the well-known efficiency droop phenomenon. Here, we show experimentally that nonpolar and semipolar orientations of GaN enable higher modulation bandwidths at low current densities where the IQE is expected to be higher and power dissipation is lower. We experimentally compare the modulation bandwidth vs. current density for LEDs on nonpolar , semipolar , and polar orientations. In agreement with wavefunction overlap considerations, the experimental results indicate a higher modulation bandwidth for the nonpolar and semipolar LEDs, especially at relatively low current densities. At 500 A/cm2, the nonpolar LED has a 3 dB bandwidth of ∼1 GHz, while the semipolar and polar LEDs exhibit bandwidths of 260 MHz and 75 MHz, respectively. A lower carrier density for a given current density is extracted from the RF measurements for the nonpolar and semipolar LEDs, consistent with the higher wavefunction overlaps in these orientations. At large current densities, the bandwidth of the polar LED approaches that of the nonpolar and semipolar LEDs due to coulomb screening of the polarization field. The results support using nonpolar and semipolar orientations to achieve high-speed LEDs at low current densities.
1 July 2019 in ACS Photonics
SMSaadat Mishkat-Ul-Masabih
Saadat Mishkat-Ul-Masabih
ARAshwin. K. Rishinaramangalam
Ashwin. K. Rishinaramangalam
+1
1 June 2020 in Optics Express
We theoretically and experimentally investigate Tamm plasmon (TP) modes in a metal/semiconductor distributed Bragg reflector (DBR) interface. A thin Ag (silver) layer with a thickness (55 nm from simulation) that is optimized to guarantee a low reflectivity at the resonance was deposited on nanoporous GaN DBRs fabricated using electrochemical (EC) etching on freestanding semipolar (20 ) GaN substrates. The reflectivity spectra of the DBRs are compared before and after the Ag deposition and with that of a blanket Ag layer deposited on GaN. The experimental results indicate the presence of a TP mode at ∼ 454 nm on the structure after the Ag deposition, which is also supported by theoretical calculations using a transfer-matrix algorithm. The results from mode dispersion with energy-momentum reflectance spectroscopy measurements also support the presence of a TP mode at the metal-nanoporous GaN DBR interface. An active medium can also be accommodated within the mode for optoelectronics and photonics. Moreover, the simulation results predict a sensitivity of the TP mode wavelength to the ambient (∼ 4-7 nm shift when changing the ambient within the pores from air with n = 1 to isopropanol n = 1.3), suggesting an application of the nanoporous GaN-based TP structure for optical sensing.
1 August 2017 in Optics Express
We report the carrier dynamics and recombination coefficients in single-quantum-well semipolar InGaN/GaN light-emitting diodes emitting at 440 nm with 93% peak internal quantum efficiency. The differential carrier lifetime is analyzed for various injection current densities from 5 A/cm2 to 10 kA/cm2, and the corresponding carrier densities are obtained. The coupling of internal quantum efficiency and differential carrier lifetime vs injected carrier density (n) enables the separation of the radiative and nonradiative recombination lifetimes and the extraction of the Shockley-Read-Hall (SRH) nonradiative (), radiative (), and Auger () recombination coefficients and their n-dependency considering the saturation of the SRH recombination rate and phase-space filling. The results indicate a three to four-fold higher A and a nearly two-fold higher B0 for this semipolar orientation compared to that of c-plane reported using a similar approach [A. David and M. J. Grundmann, Appl. Phys. Lett. 96, 103504 (2010)]. In addition, the carrier density in semipolar is found to be lower than the carrier density in c-plane for a given current density, which is important for suppressing efficiency droop. The semipolar LED also shows a two-fold lower C0 compared to c-plane, which is consistent with the lower relative efficiency droop for the semipolar LED (57% vs. 69%). The lower carrier density, higher coefficient, and lower (Auger) coefficient are directly responsible for the high efficiency and low efficiency droop reported in semipolar LEDs.