Pau Estarlich

Pau Estarlich

Auto-generated profile, based on publicly available information

Pau Estarlich

Micro and Nanotechnology Group, Emerging Thin Film Photovoltaics Lab, Universitat Politècnica de Catalunya (UPC), Barcelona, Spain

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2025 in Journal of Materials Chemistry A
Verified
Journal Article
Open access
PDF file
CGCarla Gobbo
Carla Gobbo
YGYuancai Gong
Yuancai Gong
AJAlex Jimenez-Arguijo
Alex Jimenez-Arguijo
GTGiorgio Tseberlidis
Giorgio Tseberlidis
VTVanira Trifiletti
Vanira Trifiletti
ESEdgardo Saucedo
Edgardo Saucedo
Back contact engineering of flexible (Ag,Cu)2ZnSn(S,Se)4 solar cells on Mo foil was performed. Despite the formation of a thick MoSe2 layer, MoO3 insertion at the back reduced kesterite decomposition and promoted grain growth, enabling η of 11.2%.

8 January 2025 in Solar RRL
Verified
Journal Article
Open access
GAGustavo Alvarez‐Suarez
Gustavo Alvarez‐Suarez
ALAlex J. Lopez‐Garcia
Alex J. Lopez‐Garcia
PEPau Estarlich
Pau Estarlich
JLJosé Miguel Asensi López
José Miguel Asensi López
GMGerard Masmitjà
Gerard Masmitjà
ARAlejandro Pérez Rodríguez
Alejandro Pérez Rodríguez
Transparent photovoltaic (TPV) devices represent a promising advance in photovoltaic technologies, particularly in building‐integrated photovoltaics (BIPV). Unlike conventional photovoltaics, which primarily prioritize efficiency, TPV must balance between efficiency, transparency, and aesthetics. These additional dimensions introduce unique challenges on device architecture. This article reports the development of wide‐bandgap, inorganic‐based TPV devices integrating ultrathin hydrogenated amorphous silicon (a‐Si:H) as a transparent absorber, with carrier selective contacts and transparent electrodes. The article analyzes how absorber thickness influences the electrical, optical, and aesthetic performance of devices, evaluating key parameters in TPV such as light utilization efficiency (LUE), average photopic transmittance (APT), color rendering index (CRI), and electrical properties such as power conversion efficiency (PCE). The device structure is SLG/FTO/AZO/a‐SiCx(n)/a‐Si:H/V2Ox/AZO. This approach results in PCE ranging from 1.7% with an APT of 60% to a PCE of 4.1% with an APT of 28%, yielding LUE values between 0.9% and 1.3%. Device characterization encompasses optical spectrophotometry, J–V measurements under standard test conditions, spectral response analysis, and variable illumination measurements (VIM). Additionally, color characterization is conducted using CIE 1931 color space maps to determine the chromaticity coordinates, CRI, and the variation of color as a function of absorber thickness.

1 March 2024 in Journal of Science: Advanced Materials and Devices
Verified
Journal Article
Open access
GMGerard Masmitjà
Gerard Masmitjà
PEPau Estarlich
Pau Estarlich
GLGema Lopez-Rodriguez
Gema Lopez-Rodriguez
IMIsidro Martín
Isidro Martín
CVCristobal Voz
Cristobal Voz
POPablo Ortega
Pablo Ortega

20 October 2025 in EES Catalysis
Verified
Journal Article
Open access
PDF file
EMEdoardo Maggi
Edoardo Maggi
OSOriol Segura-Blanch
Oriol Segura-Blanch
ICIvan Caño
Ivan Caño
ATArnau Torrens
Arnau Torrens
AJAlex Jimenez-Arguijo
Alex Jimenez-Arguijo
ESEdgardo Saucedo
Edgardo Saucedo
This work reports the highest photoelectrochemical (PEC) performance for selenium (Se)-based photocathodes, achieved through a simple, sustainable, and nanoparticle-free design. A half-cell solar-to-hydrogen (HC-STH) efficiency of 2.78 ± 0.01% and a photocurrent density of 11.35 ± 0.01 mA/cm2 at 0 VRHE were obtained with bare Mo/Se devices tested in H2SO4, surpassing the previous Se-based (FTO/Se/TiO2/Pt) HC-STH benchmark by over a factor of seven. To improve sustainability and device safety, the deposition of a thin TiO2 passivation layer enabled comparable performance (2.76 ± 0.01%), even in neutral phosphate buffer, allowing to obtain the highest photoelectrocatalytic onset potential reported so far (0.74 VRHE). Unlike most PEC devices that rely on complex multilayer stacks and costly noble metals, which limit scalability and environmental compatibility, this work demonstrates that high performance can be achieved with a fully earth-abundant and low-toxicity materials set. A systematic screening of back contacts, Se phases, absorber thickness, protective overlayers, and electrolyte formulations revealed the crucial role of Mo in enhancing Se orientation, charge extraction, and photovoltage generation. These results establish multiple benchmarks for Se-based PEC water splitting and highlight the potential of streamlined and scalable architectures for efficient and sustainable green hydrogen production.

23 September 2025 in Renewable Energy
Verified
Journal Article
Open access
PEPau Estarlich
Pau Estarlich
GÁGustavo Álvarez-Suárez
Gustavo Álvarez-Suárez
ALAlex J. Lopez-Garcia
Alex J. Lopez-Garcia
JAJosé Miguel Asensi
José Miguel Asensi
CVCristóbal Voz
Cristóbal Voz
GMGerard Masmitjà
Gerard Masmitjà

13 July 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
MSMaximilian Spellauge
Maximilian Spellauge
SLSergio Vela Liñán
Sergio Vela Liñán
PEPau Estarlich
Pau Estarlich
GMGerard Masmitja
Gerard Masmitja
Cristobal VozCristobal Voz
Cristobal Voz
DRDavid Redka
David Redka
Laser-based selective thin film removal is a key process in microelectronics manufacturing, where functional layers must be removed with high precision while preserving the integrity of the underlying substrate. In many technologically relevant systems, thin films are covered by additional capping layers, whose influence on the removal mechanisms remains poorly understood. In this work, we investigate the selective laser removal of VOx and AZO-capped VOx thin films deposited on silicon using time-resolved pump–probe microscopy in combination with final state crater analysis. For both systems, thin film removal is governed by indirectly induced ablation, whereby laser energy is predominantly absorbed in the silicon substrate, leading to stress-driven film lift-off. At higher fluences, the onset of phase explosion induces substrate damage and prevents selective thin film removal. The presence of the AZO capping layer reduces the processing fluence window for selective thin film removal by approximately 30%, enhances the confinement of the molten substrate and suppresses silicon substrate removal. In addition, residual fragments of the capping layer remain on the surface after processing. These findings demonstrate that capping layers significantly alter both the process window and the underlying removal dynamics and must therefore be carefully considered in the design and optimization of laser-based thin film removal processes.