1 May 2015 in Review of Scientific Instruments
Compact solid-state system is the main development trend in pulsed power technologies. A compact solid-state high-voltage nanosecond pulse generator with output voltage of 300 kV amplitude, 10 ns duration (FWHM), and 3 ns rise-time was designed for a dielectric wall accelerator. The generator is stacked by 15 planar-plate Blumlein pulse forming lines (PFL). Each Blumlein PFL consists of two solid-state planar transmission lines, a GaAs photoconductive semiconductor switch, and a laser diode trigger. The key components of the generator and the experimental results are reported in this paper.
12 April 2019 in IEEE Transactions on Plasma Science
This paper presents an experimental study on the failure mechanism of high-current gallium arsenide photoconductive semiconductor switches (GaAs PCSSs) triggered by the laser diode. We propose a Blumlein pulse forming line to test the GaAs PCSS. The result shows that the damage of GaAs PCSS almost occurs at the anode under the circumstances that either anode or cathode is illuminated, since the highest amplitude of Gunn oscillation always occurs on the anode. We speculate that the failure of high-current GaAs PCSS is attributed to the Gunn effect according to the statistics about failure factors of GaAs PCSS. We use a scanning electron microscope to semiquantitatively analyze the compositions of the erosions microball or granules, which are gallium and arsenium. The result proves our speculation.
1 September 2005 in Applied Surface Science
11 October 2011 in Physical Review Special Topics - Accelerators and Beams
An investigation on the plasma-induced field emission (PFE) properties of a large area carbon nanotube (CNT) cathode on a 2 MeV linear induction accelerator injector is presented. Experimental results show that the cathode is able to emit intense electron beams. Intense electron beams of are obtained from the cathode. The CNT cathode desorbs gases from the CNTs during the PFE process. The fast cathode plasma expansion affects the diode perveance. The amount of outgassing is estimated to be , and the ratio of outgassing and electron are roughly calculated to be within the range of 170–350 atoms per electron. The effect of the outgassing is analyzed, and the outgassing mass spectrum of the CNT cathode has been studied during the PFE. There is a significant desorption of , , and gases, which plays an important role during the PFE process. All the experiments demonstrate that the outgassing plays an important role in the formation of the cathode plasma. Moreover, the characteristic turn-on time of the CNT cathode was measured to be 39 ns. DOI: http://dx.doi.org/10.1103/PhysRevSTAB.14.104701 Published by the American Physical Society under the terms of the Creative Commons Attribution 3.0 License. Further distribution of this work must maintain attribution to the author(s) and the published article’s title, journal citation, and DOI. Published by the American Physical Society
12 July 2011 in Chinese Science Bulletin
Carbon nanotube (CNT) films were grown on silicon wafers with and without a nickel layer (Si-CNT and Ni-CNT) via the pyrolysis of iron phthalocyanine. The nickel layer was prepared using the electroless plating method. To study the emission stability of Si-CNT and Ni-CNT cathodes during intense pulsed emission, emission characteristics were measured repeatedly with a diode structure using a Marx generator as a voltage source. For the peak values of the pulsed voltage, which were in the range between 1.62–1.66 MV (corresponding to electric field intensities between 11.57–11.85 V/μm), the first cycle emission current was 109.4 A for Si-CNT and 180.5 A for Ni-CNT. By comparing the normalized emission currents of the Si-CNT and Ni-CNT cathodes, the improvement in the emission stability can be easily quantified. The number of emission cycles necessary for the peak current to decay from 100% to 50% increased from ∼3 for Si-CNT to ∼11 for a Ni-CNT film.
1 May 2020 in Review of Scientific Instruments
By utilizing the radio-frequency metal-oxide-semiconductor field-effect transistor switch, the multi-stage stacked printed circuit board Blumlein lines, and the induction voltage adder, a voltage generator with MHz repetition rates and nanosecond duration was designed and fabricated. The shunting current of the multi-stage stacked Blumlein lines, which consists of the coupling current at the load ends and the leakage current at the switch ends, is clarified. The circuit simulation and experiment of the three-stage stacked Blumlein lines are carried out; the result shows that the experiment and simulation agree well. The five-stage IVA prototype is designed for generating voltage pulses of ∼10 kV in amplitude and 8–11 ns in duration with MHz burst repetition rates. The voltage generator with MHz repetition rates and nanosecond duration demonstrated an important application prospect to reduce the electron beam initial emittance of the high energy accelerator.