Carina Amata Heck

Carina Amata Heck

Auto-generated profile, based on publicly available information

Carina Amata Heck

Technische Universität Braunschweig Institute for Particle Technology Volkmaroder Straße 5 38104 Braunschweig Lower Saxony Germany

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 November 2020 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
CHCarina Amata Heck
Carina Amata Heck
MHMax-Wolfram von Horstig
Max-Wolfram von Horstig
FHFabienne Huttner
Fabienne Huttner
JMJulian Kristoffer Mayer
Julian Kristoffer Mayer
WHWolfgang Haselrieder
Wolfgang Haselrieder
Arno KwadeArno Kwade
Arno Kwade
Low-cost and high-performance lithium ion batteries (LIBs) are a key technology in these days. One promising candidate for cathodes is the layered nickel (Ni)-rich LiNi0.8Co0.1Mn0.1O2 (NCM811) active material due to its high energy density, high specific capacity and lower material costs as well as social aspects concerning mining due to the diminished cobalt content. However, the lower thermal stability and higher sensitivity to H2O and CO2 result in a potential stronger performance degradation and lower safety. Therefore, process adaptions are inevitable. In this paper the current status and challenges of the entire cathode production process with NCM811 as active material are reviewed taking quality, cost and environmental aspects into account. General important aspects within the process are presented which are specially extended to NCM811 cathode production. Process recommendations are highlighted and innovative approaches like a water-based or solvent-free processing are discussed in comparison to conventional production technologies.

27 October 2022 in Batteries & Supercaps
Verified
Journal Article
Open access
MBMattis Batzer
Mattis Batzer
CHCarina Heck
Carina Heck
PMPeter Michalowski
Peter Michalowski
Arno KwadeArno Kwade
Arno Kwade
Solid‐state batteries possess the potential to combine increased energy densities, high voltages, as well as safe operation and therefore are considered the future technology for electrical energy storage. In particular, sulfides as solid electrolyte are promising candidates due to their high ionic conductivities and the possibility of a scalable production. This review aims to demonstrate ways to manufacture suspension‐based sulfidic solid‐state batteries both on a laboratory scale and on an industrial level, focusing on the assessment of current knowledge and its discussion from a process engineering point of view. In addition to the influence of process parameters during mechanochemical synthesis of the solid electrolyte, formulation strategies for electrodes and separators are presented. The process chain from dispersion to cell assembly is evaluated. Scale‐up technologies are considered in comparison to established techniques in the field of conventional lithium‐ion batteries with liquid electrolyte summarizing the current status of sulfidic solid‐state battery production.

1 June 2022 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
Julian MayerJulian Mayer
Julian Mayer
FHFabienne Huttner
Fabienne Huttner
CHCarina A. Heck
Carina A. Heck
DSDominik Steckermeier
Dominik Steckermeier
MHMax-Wolfram von Horstig
Max-Wolfram von Horstig
Arno KwadeArno Kwade
Arno Kwade
For batteries with high energy density and good fast-charge capability, NCM cathode active materials with ≥80 mol% nickel are promising due to their high specific capacities. Unfortunately, the increase in nickel content is accompanied by a high susceptibility to moisture. Therefore, nickel-rich NCM is coated or doped by the manufacturers to increase its stability. However, it is unclear if special requirements regarding ambient humidity must still be met during the whole production chain, or only after post-drying and during cell assembly. Therefore, the structure and properties of three different nickel-rich NCM active materials (one doped monocrystalline, two coated polycrystalline materials) processed at ambient atmosphere were investigated. At every process step, moisture content and microstructure were examined. Prior to cell assembly, two different post-drying procedures were applied and investigated. As validation, electrochemical tests were performed. Both polycrystalline cathodes demonstrated good physical and electrochemical properties, despite the ambient process atmosphere. Higher moisture reduction led to improved electrochemical performances at higher C-rates. Finally, a comparison between dry and normal atmosphere of the best performing material indicates that a production of high-quality nickel-rich electrodes at ambient atmosphere is possible if their exposure to moisture is short and well-designed post-drying techniques are applied.

19 February 2024 in Batteries & Supercaps
Verified
Journal Article
Open access
CHCarina Amata Heck
Carina Amata Heck
TSTimon Scharmann
Timon Scharmann
MOMarkus Osenberg
Markus Osenberg
ADAlexander Diener
Alexander Diener
IMIngo Manke
Ingo Manke
Arno KwadeArno Kwade
Arno Kwade
Continuous densification procedures such as calendering are crucial for sulfide‐based solid‐state batteries to realize industry‐relevant processing. Therefore, in this study, the impact of line load, roller circumferential speed and roll temperature on slurry‐based Li3PS4 and Li6PS5Cl separators compacted by a lab‐calender installed in an argon‐gas‐filled glovebox was investigated. While the Li3PS4 layers became fragile in calendered state, the tested Li6PS5Cl separators were more suitable for calendering due to better mechanical stability. Besides basic analysis of, for example, density, length expansion, pore size distribution and specific ionic conductivity of the Li6PS5Cl separators, 3D images of the structures were generated based on images obtained by synchrotron tomography. Here, all calendered separators showed particle breakage of the Li6PS5Cl. A slight decrease of the specific ionic conductivity with increased applied line load or pressure was observed for calendering and uniaxial pressing, respectively. However, an increase in the conductivity was obtained for an increase in the stack pressure. In addition to poorer contact with the metal current collectors at low stack pressure, it is assumed that a spring back effect after densification could negatively affect the microstructure of the separator. These results highlight that a densification of binder‐based Li6PS5Cl separators does not necessarily result in improved ionic conductivity probably due to the individual deformation behavior of the materials used.

5 September 2025 in Small
Verified
Journal Article
Open access
FFFinn Frankenberg
Finn Frankenberg
CHCarina A. Heck
Carina A. Heck
MKMaximilian Kissel
Maximilian Kissel
MLMartin A. Lange
Martin A. Lange
VFVasiliki Faka
Vasiliki Faka
Arno KwadeArno Kwade
Arno Kwade
While the effects of new solid electrolytes and active materials in cathode composites for solid‐state batteries are being intensively researched, little is known about the influence of mechanical processing on the properties of these composites. Here, the influence of mechanical process parameters on the production of Li 6 PS 5 Cl and LiNi 0.83 Co 0.11 Mn 0.06 O 2 composite cathodes applying a planetary ball milling process is systematically investigated. It is shown that the milling process has a significant influence on the microstructure of the composite by affecting the solid electrolyte particle size and the formation of electrolyte‐active material aggregates. The combination of experimental results with discrete element simulations shows that changes in microstructure with increasing energy input result in an increase in the density of heterocontacts, which improves the electrochemical performance. However, if the energy input is too high, a decrease in the crystallite size of Li 6 PS 5 Cl and an increase in strain in LiNi 0.83 Co 0.11 Mn 0.06 O 2 have a negative impact on the electrochemical performance. Subsequent dry film production of the pre‐milled composites reveals that a non‐optimized composite can be partially compensated by the high shear stresses acting during dry film production. Overall, the paramount importance of precisely controlling the milling process for the production of cathode composites is demonstrated.

16 February 2023 in Energy Technology
Verified
Journal Article
Open access
CHCarina A. Heck
Carina A. Heck
FHFabienne Huttner
Fabienne Huttner
JMJulian K. Mayer
Julian K. Mayer
OFOlga Fromm
Olga Fromm
MBMarkus Börner
Markus Börner
Arno KwadeArno Kwade
Arno Kwade
The selection of an appropriate cathode active material is important for operation performance and production of high‐performance lithium‐ion batteries. Promising candidates are nickel‐rich layered oxides like LiNixCoyMnzO2 (NCM, x+y+z=1) with nickel contents of ‘x’ 0.8, characterized by high electrode potential and specific capacity. However, these materials are associated with capacity fading due to their high sensitivity to moisture. Herein, two different polycrystalline NCM materials with nickel contents of 0.81 ‘x’ 0.83 and protective surface coatings are processed in dry‐room atmosphere (dew point of supply air TD ≈ −65 °C) at lab scale including the slurry preparation and coating procedure. In comparison, cathodes are produced in ambient atmosphere and both variants are tested in coin cells. Moreover, processing at pilot scale in ambient atmosphere is realized successfully by continuous coating and drying of the cathodes. Relevant electrode properties such as adhesion strength, specific electrical resistance, and pore‐size distribution for the individual process steps are determined, as well as the moisture uptake during calendering. Furthermore, rate capability and cycling stability are investigated in pouch cells, wherein initial specific discharge capacities of up to 190 mAh g−1 (with regard to the cathode material mass) are achieved at 0.2C.