Fabienne Huttner

Fabienne Huttner

Auto-generated profile, based on publicly available information

Fabienne Huttner

Institute for Particle Technology Technische Universität Braunschweig Volkmaroder Straße 5 38104 Braunschweig Germany

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 May 2019 in Energy Technology
Verified
Journal Article
Closed access
PDF file
FHFabienne Huttner
Fabienne Huttner
WHWolfgang Haselrieder
Wolfgang Haselrieder
Arno KwadeArno Kwade
Arno Kwade

1 September 2021 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
FHFabienne Huttner
Fabienne Huttner
ADAlexander Diener
Alexander Diener
THThilo Heckmann
Thilo Heckmann
JEJochen C. Eser
Jochen C. Eser
TATugay Abali
Tugay Abali
Arno KwadeArno Kwade
Arno Kwade
As moisture presents a critical contamination in lithium-ion batteries (LIBs), electrodes and separators need to be post-dried before cell assembly. The moisture adsorption, desorption and re-adsorption of electrodes during processing is strongly dependent on their material system, manufacturing route and microstructure. The microstructure, in turn, is significantly defined by the coating density, which is adjusted by calendering. As a consequence, the calendering step is expected to directly influence the moisture sorption behavior of electrodes. This is why the influence of different coating densities and structural properties on the moisture content of NCM622 cathodes was investigated in this study. For increasing density, an increasing moisture content was detected by Karl Fischer Titration and sorption measurements. SEM and BET analyses showed an increasing amount of NCM622 particle breakage, accompanied by a rising surface area. Hence, the increased moisture uptake of cathodes with higher density is mainly caused by a higher surface area, which results from particle cracking and breakage during calendering. Electrochemical analysis showed that the increased active surface area of cathodes with higher densities leads to a good performance during formation and at low C-rates. However, the reduced porosity impairs the ionic conductivity and causes capacity loss at higher C-rates.

30 June 2021 in Batteries & Supercaps
Verified
Journal Article
Open access
PDF file
FHFabienne Huttner
Fabienne Huttner
AMAxel Marth
Axel Marth
JEJochen C. Eser
Jochen C. Eser
THThilo Heckmann
Thilo Heckmann
JMJonas Mohacsi
Jonas Mohacsi
Arno KwadeArno Kwade
Arno Kwade
In order to reduce the residual moisture in lithium‐ion batteries, electrodes and separators need to be post‐dried prior to cell assembly. On an industrial scale, this is often conducted batch‐wise in vacuum ovens for larger electrode and separator coils. Especially for electrodes, the corresponding post‐drying parameters have to be carefully chosen to sufficiently reduce the moisture without damaging the sensitive microstructure. This requires a fundamental understanding of structural limitations as well as heat transfer and water mass transport in coils. The aim of this study is to establish a general understanding of the vacuum post‐drying process of coils. Moreover, the targeted design of efficient, well‐adjusted and application‐oriented vacuum post‐drying procedures for electrode coils on the basis of modelling is employed, while keeping the post‐drying intensity as low as possible, in order to maintain the sensitive microstructure and to save time and costs. In this way, a comparatively short and moderate 2‐phase vacuum post‐drying procedure is successfully designed and practically applied. The results show that the designed procedure is able to significantly reduce the residual moisture of anode and cathode coils, even with greater electrode lengths and coating widths, without deteriorating the sensitive microstructure of the electrodes.

1 June 2022 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
Julian MayerJulian Mayer
Julian Mayer
FHFabienne Huttner
Fabienne Huttner
CHCarina A. Heck
Carina A. Heck
DSDominik Steckermeier
Dominik Steckermeier
MHMax-Wolfram von Horstig
Max-Wolfram von Horstig
Arno KwadeArno Kwade
Arno Kwade
For batteries with high energy density and good fast-charge capability, NCM cathode active materials with ≥80 mol% nickel are promising due to their high specific capacities. Unfortunately, the increase in nickel content is accompanied by a high susceptibility to moisture. Therefore, nickel-rich NCM is coated or doped by the manufacturers to increase its stability. However, it is unclear if special requirements regarding ambient humidity must still be met during the whole production chain, or only after post-drying and during cell assembly. Therefore, the structure and properties of three different nickel-rich NCM active materials (one doped monocrystalline, two coated polycrystalline materials) processed at ambient atmosphere were investigated. At every process step, moisture content and microstructure were examined. Prior to cell assembly, two different post-drying procedures were applied and investigated. As validation, electrochemical tests were performed. Both polycrystalline cathodes demonstrated good physical and electrochemical properties, despite the ambient process atmosphere. Higher moisture reduction led to improved electrochemical performances at higher C-rates. Finally, a comparison between dry and normal atmosphere of the best performing material indicates that a production of high-quality nickel-rich electrodes at ambient atmosphere is possible if their exposure to moisture is short and well-designed post-drying techniques are applied.

7 July 2022 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
FHFabienne Huttner
Fabienne Huttner
ADAlexander Diener
Alexander Diener
AKArno Kwade
Arno Kwade
FBFranziska Beverborg
Franziska Beverborg
Moisture is considered to be one of the most critical contaminants in Lithium-ion batteries (LIBs), as it impairs the electrochemical performance and poses high safety risks. To reduce the moisture in the cells below a critical level, electrodes and separators for LIBs need to be post-dried before cell assembly. However, the moisture adsorption, desorption and re-adsorption behavior of electrodes is defined by the chosen material system, the manufacturing route and the microstructure of the coatings. The microstructure, in turn, is significantly determined by the calendering step, which predominantly aims at increasing the specific density and consequently, the volumetric energy density of the electrode coatings. As the calendering step decisively changes the microstructure of the electrode coatings, it can be assumed that it accordingly must have an impact on the moisture sorption behavior of the electrodes during further processing. The sorption equilibrium of electrode coatings mainly depends on the surface of the particles, the sorption in the binder system and, to a certain extent, on the capillary condensation. LIB cathodes are most commonly manufactured with polyvinylidene fluoride (PVDF) as a binder. PVDF is very hydrophobic, which is why we can assume that the moisture sorption of these cathodes is fundamentally determined by sorption on the surface and, to a lesser degree, on capillary condensation. In contrast, the moisture sorption of LIB anodes produced with a carboxymethyl cellulose/styrene-butadiene (CMC/SBR) binder system is assumed to be mainly defined by moisture sorption of the very hygroscopic binder system. Changes to the surface should only have a small influence. Hence, it is expected that the impact of the calendering step on the moisture sorption is far more pronounced for the cathodes than for the anodes. To prove this theory and analyze the impact of the calendering step in detail, the influence of different densities on the moisture sorption behavior, microstructural properties and electrochemical performance of NCM622 cathodes with PVDF binder and graphite anodes with CMC/SBR binder system is investigated. Therefore, the electrodes are calendered to three different densities in dry room atmosphere, post-dried in vacuum and assembled into coin cells. Focusing on the cathode, after calendering an increasing moisture content is observed for increasing density, measured by Karl Fischer Titration and proved by sorption measurements. Although post-drying significantly reduces the moisture content of the cathodes, the course trend is still the same with the lowest moisture at a low density and the highest moisture at high density. Via SEM analysis, a rising amount of active material particle cracks is detected with increasing density. BET measurements show that this phenomenon is accompanied by an increasing specific surface area. Hence, the increased moisture uptake of cathodes with higher density can be mainly traced back to their higher specific surface area, caused by particle cracking during calendering. Further analytics display that the chosen post-drying parameters lead to an increase of cohesion strength for all cathodes, whereas the influence on the electrical resistance depends on the density of the cathode. The electrochemical testing shows that the increased electrochemically active surface area of the cathodes with higher density results in a good performance during formation and at lower C-rates. However, the reduced porosity lowers the ionic conductivity and leads to capacity losses at higher C-rates. [1] Concerning the anode, as expected, the influence of the calendering step on the moisture sorption is much smaller. Although the specific surface area of the anodes also increases with rising density, a significant increase of moisture is not observed. Hence, the influence of the changes in microstructure is overlapped by the hygroscopic binder system of the anodes. Post-drying increases the adhesion strength of all anodes, whereas the electrical resistance seems to decrease to a small degree. The electrochemical analysis of the anodes shows a deterioration of performance with increasing density, due to limitations of the ionic conductivity at lower porosities. Altogether, we will show that for NCM622 cathodes with PVDF binder, the moisture uptake increases with increasing density after calendering, whereas there is no change in moisture content at graphite anodes with CMC/SBR binder system. These findings make an important contribution to a better process understanding and consequently, improved moisture management along the entire process chain of Lithium-ion batteries. [1] F. Huttner, A. Diener, T. Heckmann, J. C. Eser, T. Abali, J. K. Mayer, P. Scharfer, W. Schabel, A. Kwade, Increased Moisture Uptake of NCM622 Cathodes after Calendering due to Particle Breakage, J. Electrochem. Soc. 168 090539 (2021), doi.org/10.1149/1945-7111/ac24bb, CC BY 4.0