31 August 2021 in Eastern-European Journal of Enterprise Technologies
The paper presents studies of the system "induction generator-induction motor" with parametric asymmetry on a mathematical model to determine the quality of generated electricity in load operating modes. A mathematical model of the "induction generator-induction motor" system has been developed taking into account losses in steel and parametric asymmetry. The analysis of the transient characteristics of an induction generator when a motor load is connected in symmetrical and asymmetrical modes of operation is carried out. The results of changes in the main characteristics of an induction motor at various degrees of parametric asymmetry in the generator are presented. The quality of the generated electricity was analyzed based on the calculations of the unbalance coefficients for each of the operating modes. The assessment of the thermal state in steady-state conditions was carried out using an equivalent thermal equivalent circuit. Thermal transients were investigated when starting an induction motor from an autonomous energy source based on an induction generator. On a thermal mathematical model, the study of the effect of the output voltage asymmetry on the heating of the connected induction motor was carried out. It is shown that the asymmetry of the output voltage of an induction generator reaches 3–10 % and causes overheating of the windings in excess of the permissible values. A regression model has been developed for studying the operating conditions of an induction motor when powered by an induction generator with an asymmetry of the stator windings. The use of the obtained equations will make it possible to determine the most rational combination of factors affecting the heating of the stator windings of induction machines, in which they will not overheat above the maximum permissible temperature values of the corresponding insulation classes
30 April 2024 in Eastern-European Journal of Enterprise Technologies
The object of the study: the process of determining and managing ergonomic risks at workplaces when performing professional activities on the example of truck drivers. The problem lies in uncertainty when making decisions in occupational safety and health management systems. The hypothesis of the study was the possibility of assessing ergonomic risks in the occupational safety management systems of organizations based on the identification of regularities between the load index, typical working postures when performing operations and the intensity of joint movements. An ergonomic risk assessment algorithm was developed, taking into account the load index, which includes a sequence of eleven steps, which can be conditionally divided into three groups. The first is determination of the intensity of joint movement. The second is the determination of the impact of activity and the duration of the production task. The third is determining the impact of environmental factors. An assessment of the ergonomic risk of drivers was carried out for three types of production work: driving a vehicle, replacing a damaged wheel, and repairing a car. At the same time, the ergonomic risk assessment algorithm takes into account the worker’s individual state of health and environmental factors, as well as experience and work experience. It has been established that there is a high level of ergonomic risk during car maintenance due to the highest total load index, which is 30 % higher compared to other types of work of vehicle drivers. The practical application consists in the development of a universal check list of drivers based on an algorithm to determine the ergonomic risk of workers at workplaces, which consists of 11 steps
30 September 2022 in Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
Data analysis and predicting play an important role in managing heat-supplying systems. Applying the models of predicting the systems’ parameters is possible for qualitative management, accepting appropriate decisions relating control that will be aimed at increasing energy efficiency and decreasing the amount of the consumed power source, diagnosing and defining non-typical processes in the functioning of the systems. The article deals with comparing two methods of ma-chine learning: random forest (RF) and support vector machine (SVM) for predicting the temperature of the heat-carrying agent in the heating system based on the data of electronic weather-dependent controller. The authors use the following parameters to compare the models: accuracy, source cost and the opportunity to interpret the results and non-obvious interrelations. The time spent for defining the optimal hyperparameters and conducting the SVM model training is deter-mined to exceed significantly the data of the RF parameter despite the close meanings of the root mean square error (RMSE). The change from 15-min data to once-a-minute ones is done to improve the RF model accuracy. RMSE of the RF model on the test data equals 0.41°С. The article studies the importance of the contribution of variables to the prediction accuracy.
21 October 2020 in Eastern-European Journal of Enterprise Technologies
This paper addresses the issues relating to the use of 3-D printing tools in order to manufacture the structural elements of machines and apparatuses. The features of printing with the application of PLA-Carbon and PEEK (PEEK-Carbon) plastics have been analyzed. It is shown that printing that employs PEEK-plastic is accompanied by a series of problems associated with the high residual thermal stresses at cooling the material, as well as with the issue of adhesion to the laying surface, which should maintain its properties to a temperature of 420 °C. The causes of defects in the printing of articles with a significant process duration (longer than 12 hours) have been analyzed. It is shown that the most acute problem has been the interlayer grip, which predetermines the anisotropy of the properties of the finished product. It has been proven that the use of PEEK plastic makes it possible to produce force elements by applying special print heads. Particular attention should be paid to the reliable connection between a printed element and the base (table) because the peeling and deformation of the base surface are one of the main causes of geometric defects, which subsequently predetermine the structural defects. Mechanical tests of finished products have been performed, including vacuum and degassing research. It is established that the destruction of samples, in general, corresponds to classical ideas about the destruction of a quasi-fragile body when it comes to the phenomena occurring in the plane of the material’s layers. Thus, any form printed by a printer is an orthotropic article whose behavior is satisfactorily described by Griffiths theory. At the same time, the strength characteristics, as well as elastic properties of a product demonstrate significant axial (orthotropic) differences. It is also shown that the functional properties of a product are ensured by the comprehensive dynamic-moving and thermobaric influence on the melt of the material in the space behind a nozzle owing to which the planes of adhesion and hollowness of the finished product are formed.The recommendations have been formulated for preventing defects and the elimination of delamination phenomena, errors in the geometric parameters of a product; it has been concluded that it is appropriate to implement these processes into production
1 January 2020 in JOURNAL of Donetsk mining institute
DDDepartment of Automatic Control Systems and Electric Drive
Department of Automatic Control Systems and Electric Drive
PUProfessional College of Engineering and Management National Aviation University
Professional College of Engineering and Management National Aviation University
+3
The purpose of the work is to develop methodological foundations for optimizing the concentration of hydroaeroions from the variability of the physical factors of the working room airspace with ultrasonic ionization. Methodology. The measurements were carried out according to the developed methodology with the “Sapphire 3K” air ion counter and with the use of a TM-4001 hot-wire anemometer. To analyze the data of experimental studies, the method of mathematical planning of the experiment was used. The scheme of rotatable central compositional planning (RCSC) was used, which is based on regression analysis, including the method of least squares and statistical data processing. For all measurement results, the adequacy of the regression models was checked using the built-in statistical functions of Statgraphiks. Results. Experimental studies have shown that the use of an ultrasonic generator of air ions significantly increases the concentration of negative ions (2400 cm-3) and that is the increase in the quality of the internal working space, which is responsible for the production of ozone and nitrogen oxide. Mathematical processing of the obtained data made it possible to establish the general effect of the air flow in the room (v) and the distance to the UAG (s) on the concentration of positive and negative aerons. The influence of varying each of the studied factors on the value of the concentration of air ions was quantitatively evaluated. Scientific novelty. The synthesized regression models of hydroaerion concentrations describe the relationship between the air speed in the room and the distance to the ultrasonic generator of air ions. The adequacy of the models was checked with the coefficient of determination R2 = 86%, which indicates a high degree of connection between the coefficients of the system. Practical significance. The result obtained can be used in the design and development of a control system for an ultrasonic generator of air ions in order to create the most comfortable high-quality ionic composition of air in the working area.