Sang Ho Lee

Sang Ho Lee

Auto-generated profile, based on publicly available information

Sang Ho Lee

Department of Materials University of Oxford Oxford OX1 3PH UK

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 June 2018 in Journal of Materials Chemistry A
Verified
Journal Article
Open access
PDF file
SLSang Ho Lee
Sang Ho Lee
AMAmoghavarsha Mahadevegowda
Amoghavarsha Mahadevegowda
Chun HuangChun Huang
Chun Huang
JEJack D. Evans
Jack D. Evans
PGPatrick Grant
Patrick Grant
Self-assembled porous structures were manufactured directly onto current collectors based on layer-by-layer spray printing of TiO2(B) nanotubes. The through-thickness porous channels in the electrode structures enabled the efficient penetration of the liquid Li-ion electrolyte into the resulting coral-like electrode, leading to an improvement in thickness-dependent power capability.

1 August 2019 in Journal of Materials Chemistry A
Verified
Journal Article
Open access
PDF file
JBJunfu Bu
Junfu Bu
PLPuiki Leung
Puiki Leung
Chun HuangChun Huang
Chun Huang
SLSang Ho Lee
Sang Ho Lee
PGPatrick Grant
Patrick Grant
LiFePO4 (LFP) electrodes for Li-ion battery applications were prepared by spray printing. By optimising the substrate temperature, solvent ratio and electrode material concentration, a honeycomb pore structure was produced over a large area electrode. In a liquid electrolyte, the honeycomb structured LFP electrode showed improved cycling performance at high C-rate due to shortened pore pathways and improved Li mobility. In a solid-state configuration, a PEO(LITFSI)-Li1.5Al0.5Ge1.5(PO4)3 (PEO-LAGP) based solid electrolyte was either spray printed on top of the LFP and/or interleaved within sub-layers of the LFP electrode, for both non-honeycomb and honeycomb pore morphologies. Cross-sectional scanning electron microscope (SEM) and energy-dispersive X-ray spectroscopy (EDS) mapping combined with electrochemical impedance spectroscopy (EIS) testing showed that the honeycomb electrode with inter-leaved sub-layers of solid-state electrolyte improved interfacial contact between the electrode and electrolyte. When coupled with Li foil in a solid-state Li ion battery configuration, the honeycomb interleaved electrode also showed the best performance in terms of capacity and cycle stability at all testing temperatures, showing capability that exceeded previously reported performance.

11 November 2022 in Nano Letters
Verified
Journal Article
Closed access
MKMinho Kim
Minho Kim
SKSong Kyu Kang
Song Kyu Kang
JCJunil Choi
Junil Choi
HAHwichan Ahn
Hwichan Ahn
JJJunhyuk Ji
Junhyuk Ji
Won Bae KimWon Bae Kim
Won Bae Kim

20 June 2018 in Energy Technology
Verified
Journal Article
Closed access
PDF file
SLSang Ho Lee
Sang Ho Lee
YNYuseong Noh
Yuseong Noh
YJYong‐Ryun Jo
Yong‐Ryun Jo
YKYoongon Kim
Yoongon Kim
BKBong‐Joong Kim
Bong‐Joong Kim
Won Bae KimWon Bae Kim
Won Bae Kim

6 December 2018 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
SLSang Ho Lee
Sang Ho Lee
KLKexue Li
Kexue Li
CHChun Huang
Chun Huang
JEJack D. Evans
Jack D. Evans
PGPatrick S. Grant
Patrick S. Grant
Directional, micron-scale honeycomb pores in Li-ion battery electrodes were fabricated using a layer-by-layer, self-assembly approach based on spray printing of carbon nanofibers. By controlling the drying behavior of each printed electrode layer through optimization of (i) the volume ratio of fugitive bi-solvent carriers in the suspension, and (ii) the substrate temperature during printing, self-assembled, honeycomb pore channels through the electrode were created spontaneously and reliably on current collector areas larger than 20 cm × 15 cm. The honeycomb pore structure promoted efficient Li-ion dynamics at high charge/discharge current densities. Incorporating an optimum fraction (2.5 wt%) of high energy density Si particulate into the honeycomb electrodes provided a four-fold increase in deliverable discharge capacity at 8000 mA/g. The spray printed, honeycomb pore electrodes were then investigated as negative electrodes coupled with similar spray printed LiFePO4 positive electrodes in a full Li-ion cell configuration, providing an approximately 50 % improvement in rate capacity retention over half-cell configurations of identical electrodes at 4000 mA/g.

25 September 2019 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
SLSang Ho Lee
Sang Ho Lee
CJColin Johnston
Colin Johnston
PGPatrick S. Grant
Patrick S. Grant
Through-electrode thickness honeycomb architectures were layer-by-layer self-assembled directly through a scalable printing process for ultrapower hybrid lithium-ion capacitor applications. Initially, the electrochemical performance of the pore-array electrodes was investigated as a function of the active material type (graphene plates, carbon nanofibers, and activated carbon). Inactive components (conductive carbon and polymer binder) were then minimized to 5 wt %. Finally, an optimized activated carbon-based cathode was paired with a spray-printed Li4Ti5O12-based anode and a range of anode-to-cathode mass ratios in a lithium-ion capacitor arrangement were investigated. A 1:5 anode/cathode mass ratio provided an attractive energy density comparable with a Li4Ti5O12/LiFePO4 lithium-ion battery but with outstanding power capability that was an order of magnitude greater than typical for lithium-ion batteries. The pore-array electrode was reproduced over areas of 20 cm × 15 cm in a double-sided coated configuration, and the option for selectively patterning electrodes was also demonstrated.