Junfu Bu

Junfu Bu

Auto-generated profile, based on publicly available information

Junfu Bu

University of Oxford

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2012 in Progress in Organic Coatings
Verified
Journal Article
Closed access
RHRong-Gang Hu
Rong-Gang Hu
SZSu Zhang
Su Zhang
JBJun-Fu Bu
Jun-Fu Bu
CLChang-Jian Lin
Chang-Jian Lin
Guang-Ling SongGuang-Ling Song
Guang-Ling Song

25 August 2016 in Journal of Materials Chemistry A
Verified
Journal Article
Closed access
PDF file
JLJulia Lyagaeva
Julia Lyagaeva
NDNikolay Danilov
Nikolay Danilov
GVGennady Vdovin
Gennady Vdovin
JBJunfu Bu
Junfu Bu
Dmitry MedvedevDmitry Medvedev
Dmitry Medvedev
Panagiotis TsiakarasPanagiotis Tsiakaras
Panagiotis Tsiakaras
The present work describes the features of the synthesis and physicochemical and electrical properties of a new Dy-doped BaCeO 3 –BaZrO 3 proton-conducting electrolyte as well as its application in a reversible solid oxide fuel cell.

1 December 2014 in Journal of Power Sources
Verified
Journal Article
Closed access
JBJunfu Bu
Junfu Bu
PJPär G. Jönsson
Pär G. Jönsson
ZZZhe Zhao
Zhe Zhao

4 September 2025 in Nature Energy
Verified
Journal Article
Open access
PDF file
DMDominic L. R. Melvin
Dominic L. R. Melvin
MSMarco Siniscalchi
Marco Siniscalchi
DSDominic Spencer-Jolly
Dominic Spencer-Jolly
BHBingkun Hu
Bingkun Hu
ZNZiyang Ning
Ziyang Ning
Peter G. BrucePeter G. Bruce
Peter G. Bruce
Avoiding lithium dendrites at the lithium/ceramic electrolyte interface and, as a result, avoiding cell short circuit when plating at practical current densities remains a significant challenge for all-solid-state batteries. Typically, values are limited to around 1 mA cm −2 , even, for example, for garnets with a relative density of >99%. It is not obvious that simply densifying ceramic electrolytes will deliver high plating currents. Here we show that plating currents of 9 mA cm −2 can be achieved without dendrite formation, by densifying argyrodite, Li 6 PS 5 Cl, to 99%. Changes in the microstructure of Li 6 PS 5 Cl on densification from 83 to 99% were determined by focused ion beam-scanning electron microscopy tomography and used to calculate their effect on the critical current density (CCD). Modelling shows that not all changes in microstructure with densification act to increase CCD. Whereas smaller pores and shorter cracks increase CCD, lower pore population and narrower cracks act to decrease CCD. Calculations show that the former changes dominate over the latter, predicating an overall increase in CCD, as observed experimentally.

8 September 2019 in Advanced Energy Materials
Verified
Journal Article
Open access
PDF file
PLPuiki Leung
Puiki Leung
JBJunfu Bu
Junfu Bu
PVPablo Quijano Velasco
Pablo Quijano Velasco
MRMatthew R. Roberts
Matthew R. Roberts
NGNicole Grobert
Nicole Grobert
PGPatrick Grant
Patrick Grant
A symmetric solid‐state battery based on organic porous electrodes is fabricated using scalable spray‐printing. The active electrode material is based on a textile dye (disperse blue 134 anthraquinone) and is capable of forming divalent cations and anions in oxidation and reduction processes. The resulting molecule can be used in both negative and positive electrode reactions. After spray printing an inter‐connected pore honeycomb electrode, a solid‐state electrolyte (σLi: × 10−4 S cm−1) based on a polymeric ionic liquid is spray‐printed as a second layer and infiltrated through the porous electrodes. A symmetric all‐organic battery is then formed with the addition of another identical set of electrode and electrolyte layers. Both density functional theory calculations and charge‐discharge profiles show that the potentials for the negative and positive electrode reactions are amongst the lowest (≈2.0 V vs Li) and the highest (≈3.5 V vs Li), respectively, for quinone‐type molecules. Over the C‐rate range 0.2 to 5 C, the battery has a discharge cell voltage of more than 1 V even up to 250 charge‐discharge cycles and capacities are in the range 50–80 mA h g−1 at 0.5 C.

1 August 2019 in Journal of Materials Chemistry A
Verified
Journal Article
Open access
PDF file
JBJunfu Bu
Junfu Bu
PLPuiki Leung
Puiki Leung
Chun HuangChun Huang
Chun Huang
SLSang Ho Lee
Sang Ho Lee
PGPatrick Grant
Patrick Grant
LiFePO4 (LFP) electrodes for Li-ion battery applications were prepared by spray printing. By optimising the substrate temperature, solvent ratio and electrode material concentration, a honeycomb pore structure was produced over a large area electrode. In a liquid electrolyte, the honeycomb structured LFP electrode showed improved cycling performance at high C-rate due to shortened pore pathways and improved Li mobility. In a solid-state configuration, a PEO(LITFSI)-Li1.5Al0.5Ge1.5(PO4)3 (PEO-LAGP) based solid electrolyte was either spray printed on top of the LFP and/or interleaved within sub-layers of the LFP electrode, for both non-honeycomb and honeycomb pore morphologies. Cross-sectional scanning electron microscope (SEM) and energy-dispersive X-ray spectroscopy (EDS) mapping combined with electrochemical impedance spectroscopy (EIS) testing showed that the honeycomb electrode with inter-leaved sub-layers of solid-state electrolyte improved interfacial contact between the electrode and electrolyte. When coupled with Li foil in a solid-state Li ion battery configuration, the honeycomb interleaved electrode also showed the best performance in terms of capacity and cycle stability at all testing temperatures, showing capability that exceeded previously reported performance.