Dhruv Patel

Dhruv Patel

Auto-generated profile, based on publicly available information

Dhruv Patel

Edward S. Rogers Sr. Department of Electrical and Computer Engineering, University of Toronto, Toronto, ON, Canada

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 November 2022 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Open access
DPDhruv Patel
Dhruv Patel
ASAlireza Sharif-Bakhtiar
Alireza Sharif-Bakhtiar
TCTony Chan Carusone
Tony Chan Carusone
A flip-chip co-packaged linear transimpedance amplifier (TIA) in 16-nm fin field effect transistor (FinFET) CMOS demonstrating 112-Gb/s four-level pulse-amplitude modulation (4-PAM) with −8.2-dBm sensitivity is presented in support for optical receivers required in the next-generation intra-data center links. A proposed three-stage TIA is comprised of a shunt-feedback stage followed by digitally programmable continuous-time linear equalizers (CTLEs) and a variable gain amplifier (VGA). Broadband low-noise design is achieved by having the first stage with much lower bandwidth (BW) followed by the proposed BW recovering CTLEs. A low-power design is supported by the inverter-based single-ended architecture with a single-ended-to-pseudo-differential conversion in the last stage. TIA’s BW extension is further supported by optimizing the photodiode-to-receiver (PD-to-RX) interconnect and utilizing several inductive peaking techniques. It achieves 63-dB $\Omega $ gain, 32-GHz BW, and an average input-referred current noise density of 16.9 pA/ $\sqrt {\text {Hz}}$ while operating at 0.9-V supply and consuming 47-mW power. Opto-electrical measurements are performed on a co-packaged prototype comprised of identical proposed TIAs in CMOS with combinations of various commercial PDs and PD-to-RX interconnect lengths confirming 112-Gb/s 4-PAM reception meeting pre-forward error correction (FEC) symbol error rate (SER) of $4.8 \times 10 ^{-4}$ without any post-equalization.

27 May 2021 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
DPDhruv Patel
Dhruv Patel
ANAdam Neale
Adam Neale
DWDerek Wright
Derek Wright
MSManoj Sachdev
Manoj Sachdev
This paper proposes a Differential-Input Body Bias Sense Amplifier (DIBBSA) with an auto-offset mitigation feature suitable for low-voltage SRAMs where the differential bitline signals are applied to the sources as well as to the body of the critical sensing transistors. We simulated and fabricated the proposed DIBBSA architecture with various operational modes in 65-nm CMOS technology to analyze body biasing's effectiveness in mitigating the offset. The standard deviation of offset ( σ OS ) was measured over 5120 SAs in 10 ICs. The iso-gate area reduction in σ OS for the proposed DIBBSA-FL and DIBBSA-PD modes resulted in 68.1% and 61.9% compared to conventional Current Latch SA (CLSA) and 24.1% and 18.1% compared to Voltage Latch SA (VLSA) at 0.4 V supply and 25 °C, respectively. Carried out measurements on 512 SAs in an IC show the minimum required differential input voltage across the temperature range of 0 °C to 75 °C at 0.4 V is achieved to be 48% lower compared to CLSA and 28% lower compared to VLSA by both the DIBBSA-FL and DIBBSA-PD modes.

5 March 2019 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
DPDhruv Patel
Dhruv Patel
ANAdam Neale
Adam Neale
DWDerek Wright
Derek Wright
MSManoj Sachdev
Manoj Sachdev
Sense amplifier (SA) input-referred offset often dictates the minimum required differential input (Δ VBL-min) and is an important factor in realizing low-voltage static random access memories. This paper presents a HYbrid latch-type Sense Amplifier (HYSA-QZ), where the bitline signals are supplied to multiple internal nodes to significantly reduce Δ VBL-min. A 65-nm CMOS test chip with arrays of the HYSA-QZ, two intermediate formulations of the HYSA-QZ, conventional current latch SA (CLSA), and conventional voltage latch SA (VLSA) were fabricated. Measurements over 5120 SAs of each type show that the HYSA-QZ implemented with regular-V T transistors require 50.0%, and 22.8% lower Δ VBL-min with 6.5% (or 4.5%) and 30.7% (or 18.8%) of total gate (or layout) area overhead compared to CLSA and VLSA at 0.4 V, respectively. Iso-gate-area offset improvement was substantiated with Pelgrom's mismatch model, where the HYSA-QZ with regular- V T transistors showed 46.6% and 7.7% improvements in measured standard deviation of offset distribution compared with CLSA and VLSA, respectively. Measured Δ VBL-min for the HYSA-QZ remains stable and low over a temperature range from 0 °C to 75 °C at 0.4 V. Moreover, an additional 13.0% reduction in Δ VBL-min was measured in the HYSA-QZ when using low-V T transistors. Finally, the HYSA-QZ operates reliably at VDD-min of 260 mV in 25 °C.

23 January 2018 in IEEE Solid-State Circuits Letters
Verified
Journal Article
Closed access
DPDhruv Patel
Dhruv Patel
MSManoj Sachdev
Manoj Sachdev
An offset tolerant SRAM sense amplifier (SA) deployed with sample-boost-latch technique to facilitate both common mode and differential mode boosting is proposed. The common mode boosting enables proposed SA, SBLSA to operate deeper into the subthreshold regime whereas the differential mode boosting helps tolerate undesirable mismatch conditions by driving cross-coupled inverters with boosted differential voltages. The proposed boosting circuit first samples the bitline voltages and then isolates the sampled voltages from the highly capacitive bitlines followed by the boosting phase on relatively much less internal input capacitances of the latch. Arrays of SBLSA and conventional voltage latch SA (VLSA) were fabricated in 65-nm-GP CMOS (512 each). At 25 °C, SBLSA achieves 23.3% reduction in directly measured standard deviation of input-referred offset (across 16 ICs, 8192 SAs) and 38.5% improvement (typical IC) in sensing delay at 0.3 V. SBLSA offers reliable operation across entire temperature range of -25 °C to 85 °C at 0.35 V whereas it is 0.41 V for VLSA. Finally, SBLSA operates reliably at the minimum supply of 0.23 V at 25 °C which is 30 mV less compared to VLSA.

23 August 2023 in IEEE Transactions on Signal and Power Integrity
Verified
Journal Article
Open access
BRBahaa Radi
Bahaa Radi
ZLZonghao Li
Zonghao Li
DPDhruv Patel
Dhruv Patel
ACAnthony Chan Carusone
Anthony Chan Carusone
This paper addresses the optimization of the interface between the photodetector (PD) and the analog front-end (AFE) in high-speed, high-density optical communication receivers. Specifically, the paper focuses on optimizing design elements in the interface, including the interconnecting transmission line, the T-coil, the transimpedance amplifier (TIA), and digital equalization tap weights. To optimize the optical link, we use a combination of analytical models, electromagnetic simulations (EM), and machine learning (ML) techniques to describe different interface elements as most appropriate for each. Finally, we use the genetic algorithm to obtain optimal design parameters. The proposed optimization approach leads to a quick design time and reveals insights into some of the best design practices. As an example, we use the proposed method to investigate the relationship between optimal transmission line width and the amount of equalization available on the receiver. These conclusions are further supported by measurements taken on an assembled prototype with various PD-to-TIA interconnect lengths.