3 December 2025 in IEEE Electron Device Letters
In this work, we propose a first-order anti-symmetric (A1) mode acoustic resonator and filter based on a 128° YX-cut LiNbO3 (LN) solidly mounted resonator (SMR) structure. By adopting a non-periodic Bragg reflection layer structure, shear waves and longitudinal waves are effectively reflected at the designed frequency, reducing acoustic leakage loss and achieving a spurious-free resonator within the passband. Simulation results show that the frequency of the spurious-free A1 mode SMR can be adjusted in a wide-frequency range by optimizing the half period and metal ratio simultaneously, which is distinct from the conventional XBAR method that relies on LN film thinning. Then a 6th-order T-type A1 mode SMR filter was designed and fabricated, which exhibits a center frequency of 6.82 GHz, a minimum insertion loss of 2.2 dB, a 3dB bandwidth of 740 MHz, and out-of-band suppression exceeding 25 dB. This work demonstrates a SMR filter design method suitable for the A1 mode, and provides a feasible path and design ideas for engineering implementation of high-frequency acoustic filters.
1 January 2026 in IEEE Microwave and Wireless Technology Letters
10 July 2026 in International Journal of Microwave and Wireless Technologies
With the evolution from 5G to 6G and the popularization of carrier aggregation technology, mobile terminal devices face challenges in miniaturizing multiplexers and handling concurrent signals across a wide-bandgap. This study proposes a numerical de-embedding design method. By precisely calculating and compensating for the parasitic loads, it achieves deterministic synthesis of matching networks. Based on this method, we designed and fabricated a monolithic integrated surface acoustic wave triplexer on a lithium tantalite on insulator (LTOI) substrate for dual-frequency GPS L1/L5 positioning and Bluetooth (BT) communication. To suppress a specific spurious mode on the LTOI substrate and improve the isolation, a notch inductor structure was embedded into the design. The monolithic integrated triplexer measures 2.5 mm × 2.0 mm × 0.6 mm after packaging. The insertion loss is less than 1.6 dB in both the L1 and L5 bands. In the BT band, the average loss within any 18 MHz range of the passband is below 2.5 dB. The return loss for all three channels is better than −10 dB, while the isolation between channels is maintained at ≈40 dB. The successful fabrication of this triplexer not only validates the design method but also demonstrates its potential for application in miniaturized wearable devices.
1 August 2026 in IEEE Transactions on Microwave Theory and Techniques
1 January 2026 in IEEE Transactions on Electron Devices
10 March 2026 in IEEE Transactions on Electron Devices
This work investigates shear horizontal surface acoustic wave (SH-SAW) resonators based on a Bragg reflector. The performances of the SH-SAW resonators are systematically analyzed by finite element method (FEM) simulation. The influences of the high acoustic-impedance (HAI) and low-acoustic-impedance (LAI) layers on the performances of the resonators are investigated, and the effect of the substrate material is also discussed. By using a Ta2O5/SiO2 single-pair Bragg reflector, the SH-SAW resonator shows good performances due to the confinement of acoustic energy within the LiTaO3 (LT) thin film. A series of SH-SAW resonators with different wavelengths was prepared. The prepared resonators exhibit a maximum Bode $\textit{Q}$ factor (Q ${}_{\text{max} }\text {)}$ of 2513 and an effective electromechanical coupling coefficient (K ${}^{\text{2}}_{\text {eff}}\text {)}$ of 8.38%. The influences of the lattice damage and residual stress on Qmax in the LT film are also discussed. Notably, the proposed SH-SAW based on a Bragg reflector demonstrates intrinsic advantages, including the elimination of the parasitic surface conduction (PSC) effect and reduced substrate dependency, which provides an alternative way of developing high-performance SH-SAW resonators.