3 December 2025 in IEEE Electron Device Letters
In this work, we propose a first-order anti-symmetric (A1) mode acoustic resonator and filter based on a 128° YX-cut LiNbO3 (LN) solidly mounted resonator (SMR) structure. By adopting a non-periodic Bragg reflection layer structure, shear waves and longitudinal waves are effectively reflected at the designed frequency, reducing acoustic leakage loss and achieving a spurious-free resonator within the passband. Simulation results show that the frequency of the spurious-free A1 mode SMR can be adjusted in a wide-frequency range by optimizing the half period and metal ratio simultaneously, which is distinct from the conventional XBAR method that relies on LN film thinning. Then a 6th-order T-type A1 mode SMR filter was designed and fabricated, which exhibits a center frequency of 6.82 GHz, a minimum insertion loss of 2.2 dB, a 3dB bandwidth of 740 MHz, and out-of-band suppression exceeding 25 dB. This work demonstrates a SMR filter design method suitable for the A1 mode, and provides a feasible path and design ideas for engineering implementation of high-frequency acoustic filters.
1 January 2026 in IEEE Transactions on Electron Devices
10 March 2026 in IEEE Transactions on Electron Devices
This work investigates shear horizontal surface acoustic wave (SH-SAW) resonators based on a Bragg reflector. The performances of the SH-SAW resonators are systematically analyzed by finite element method (FEM) simulation. The influences of the high acoustic-impedance (HAI) and low-acoustic-impedance (LAI) layers on the performances of the resonators are investigated, and the effect of the substrate material is also discussed. By using a Ta2O5/SiO2 single-pair Bragg reflector, the SH-SAW resonator shows good performances due to the confinement of acoustic energy within the LiTaO3 (LT) thin film. A series of SH-SAW resonators with different wavelengths was prepared. The prepared resonators exhibit a maximum Bode $\textit{Q}$ factor (Q ${}_{\text{max} }\text {)}$ of 2513 and an effective electromechanical coupling coefficient (K ${}^{\text{2}}_{\text {eff}}\text {)}$ of 8.38%. The influences of the lattice damage and residual stress on Qmax in the LT film are also discussed. Notably, the proposed SH-SAW based on a Bragg reflector demonstrates intrinsic advantages, including the elimination of the parasitic surface conduction (PSC) effect and reduced substrate dependency, which provides an alternative way of developing high-performance SH-SAW resonators.
16 October 2026 in SSRN Electronic Journal
This work investigates the parasitic surface conduction (PSC) effect suppression in silicon‐integrated single‐crystalline LiNbO3 (LN) thin-film by two-times He+ implanted high-resistivity Si (HR‐Si) substrate. First, the effect of He+ implantation energy on vacancy defects depth distribution in HR-Si is studied. The trap layer thickness induced by one-time He+ implantation is less than 500 nm, which is insufficient for PSC effect suppression. Therefore, two-times He+ implantations are adopted. The trap layer thickness induced by two-times He+ implantations is 670nm, which is sufficient for PSC effect suppression. In the experiment, the resistivity and carrier concentration of the He+ implanted samples annealed at different temperatures are studied. Results indicate that the sample annealed at 600 °C can suppress the PSC effect, and subsequent lower‐temperature annealing has little effect. Two single‐crystalline LN thin-film wafers based on HR-Si substrates with and without He+ implantation are fabricated. Finally, loss characteristics of the two wafers are measured. Compared with the wafer without ion implantation, the wafer with two-times He+ implanted HR-Si substrate exhibits a higher Q-value. This work indicates that the single‐crystalline LN thin-film on two-times He+ implanted HR‐Si substrate can suppress the PSC effect. This may pave a new way to realize higher-performance surface-acoustic-wave devices.