Olanrewaju Bilikis Gbadamosi Olatunde

Olanrewaju Bilikis Gbadamosi Olatunde

Auto-generated profile, based on publicly available information

Olanrewaju Bilikis Gbadamosi Olatunde

Olabisi Onabanjo University, Nigeria

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 December 2022 in Progress in Aerospace Sciences
Verified
Journal Article
Closed access
VUVamsi Krishna Undavalli
Vamsi Krishna Undavalli
OOOlanrewaju Bilikis Gbadamosi Olatunde
Olanrewaju Bilikis Gbadamosi Olatunde
RBRahim Boylu
Rahim Boylu
CWChuming Wei
Chuming Wei
JHJosh Haeker
Josh Haeker
BKBhupendra Khandelwal
Bhupendra Khandelwal

12 November 2024 in Progress in Aerospace Sciences
Verified
Journal Article
Closed access
CWChuming Wei
Chuming Wei
VUVamsi Krishna Undavalli
Vamsi Krishna Undavalli
CPChris Perkins
Chris Perkins
KHKatie Heglas
Katie Heglas
EOEthan Oswald
Ethan Oswald
BKBhupendra Khandelwal
Bhupendra Khandelwal

8 September 2021 in Mechanical Engineering for Society and Industry
Verified
Journal Article
Open access
PDF file
OAOlayide Adetunji
Olayide Adetunji
MOMontfort C. Ogbuokiri
Montfort C. Ogbuokiri
ODOlawale U. Dairo
Olawale U. Dairo
OOOlanrewaju B. Olatunde
Olanrewaju B. Olatunde
IOIliyas K. Okediran
Iliyas K. Okediran
Industrial excess heat is a largely untapped resource that has the potential for external use that would be beneficial to the cement industry. Therefore, this work studied the excess heat utilization for the optimization of production cost in a cement plant within a period of three years. The study of plant layout in the selected plant in Nigeria (Ewekoro II Cement Plant of 200 tonnes/hour) was carried out to identify areas where excess heat is generated. The temperature and static pressure of precalciner, kiln, and cyclone were taken using a temperature probe, pitot tube, digital manometer, and light-emitting diode temperature reader. These parameters were used to obtain the mass flow rate and heat transfer needed for the heat energy analysis of the system. The kiln was maintained at constant tonnage per hour through a clinker truck weighed using the weighbridge. The result showed that the heat generated from the kiln was 577,640,260 MJ/hr. through excess air draft of 780,000 m3/hr (89.4%) at 250 °C and induced draft fan of 900,000 m3/hr at 350 °C. The result showed that excess heat can be utilized in pre-heater and air quenched cooler boilers, steam turbines and auxiliaries, and generators. The total estimated heat that could be saved amounted to 344,648,250 MJ with a total annual capacity of 2.25 million tonnes of cement. A saving of over two billion dollars could be achieved in production cost per year.

1 July 2021 in IIUM Engineering Journal
Verified
Journal Article
Open access
PDF file
ADA. A. Dare
A. A. Dare
OOOlanrewaju Olatunde
Olanrewaju Olatunde
OIO. S. Ismail
O. S. Ismail
ASA. S. Shote
A. S. Shote
OAO. J. Alamu
O. J. Alamu
MSM. A. Sulaiman
M. A. Sulaiman
This research is aimed at investigating the effect of using ethanol (E100) in multi-zone model analysis consisting of multi-combustion chamber zoning cases. The first case considered is a three-zone model that has an unburned zone, burned zone, and transitory zone. The second case model is also three-zone, consisting of an unburned zone and two partitioned burned zones. The burned zone was imagined partitioned into burned zone-1 and burned zone-2 under uneven fuel distribution having different equivalent ratios. The third case is a four-zone model including two regions of burned zone, an unburned zone and a transitory zone, which is unburned burned zone containing a mixture of unburned and burned gases. Arbitrary constants for each of the unburned (CC1) and burned (CC2) Zone leakages in the unburned burned Zone are 0.00025, 0.0005, 0.001, 0.002, 0.005, 0.1 and 0.5. The Mass Fraction Burned (MFB) for zone-1, x1 and burned zone-2, x2 are computed using Partitioned Burnt Zones Ratios (PBZR) of 2:8, 3:7, 4:6, 5:5, 6:4, 7:3 and 8:2. Two equivalent ratios, one for each fuel MFB (phi 1, phi 2), (0.8, 0.6) and (0.6, 0.8) are analyzed using fuel blends of varying percentage. A comparison of values of the three zoning cases is done using peak values from the three-zone models to evaluate the four-zone model. The model was compared with a spark ignition engine (SIE) operating with a premium motor spirit (PMS) serving as baseline. The engine operating conditions were set at an engine speed of 2000 rpm, -35bTDC ignition time, and burn duration at 60 degrees C. The indicated mean effective pressure (IMEP), thermal efficiency (eta), cylinder pressure and emission fraction from the developed models and those of two-zone analysis obtained agreed with literature values. The result showed it is undesirable to have a high volume of burned charge as infiltrate. The three-zone segmented model predicted the highest engine thermal efficiency and peak pressure at mass burn ratio of 7:3. A general reduction in N-2 emission was observed for the three-zone transitional and four-zone models.