2 May 2022 in IEEE Transactions on Circuits and Systems I: Regular Papers
A charge amplifier incorporates digital circuits as an alternative to the classic analog amplifier to achieve a high open-loop gain to maintain a consistent closed-loop gain over input capacitance variations. The digital-assisted charge amplifier employs a comparator, digital control logic, differential charge pump, current sources, common-mode feedback, and clock generator. A detailed analysis studies the amplifier stability and trade-off between ripple voltage and settling speed. A novel two-step reset scheme and tri-state charge pump minimize the output offset due to ripple residues. Fabricated in a 180-nm CMOS process, the digital-assisted amplifier achieves an open-loop gain of 101 dB, closed-loop gain of $15.0~\mu \text{V}$ /e-, input-referred noise of 221 $\text{e}^{-}$ rms, and output swing of 3 V while consuming 2.19 mW. The amplifier also demonstrates the ability to amplify a dynamic input current using a custom opto-electronic test setup. The amplifier maintains a consistent closed-loop gain across parasitic input capacitance from 6 pF to 94 pF.
17 June 2020 in IEEE Transactions on Instrumentation and Measurement
We describe a charge detector that utilizes a high-gain, differential solid-state amplifier with active reset and a novel technique to measure the gain using a custom optoelectronic system. Implemented in a 180-nm complementary metal-oxide-semiconductor (CMOS) process, the amplifier realizes a high gain of 8.9 μV/e- and single-pass rms noise of 475 e- for 10 ms time interval with a 300 kHz lowpass filter corner. Operating at a sampling frequency of 10 kHz, the active reset extends the dynamic range of the detector. The amplifier is the first instance of a charge detector that combines a differential topology, active reset, and small feedback capacitors for low-noise, high-gain, high-dynamic-range, and robust operations. The proposed optoelectronic test system injects an adjustable input photocurrent as low as 33 pA to precisely quantify the detector’s gain without the need for a known calibration capacitance. The amplifier is directly wire-bonded to a PCB that has a built-in 1 cm2 Faraday cup. The gain and noise performance have been characterized for a range of input capacitance and the results show good agreement with simulations. The test system additionally demonstrates the ability to inject a time-varying input at the pA levels to characterize the dynamic response of the detector. An electrospray system confirms that the detector responds to free-space charge and that it can process an input as large as 56,000 e- without saturation. The compact and high sensitivity design qualify the device for use in charge detection applications such as mass spectrometry and space instruments.
4 April 2024 in IEEE Solid-State Circuits Letters
The design and measurement of a time-domain analog spiking neuron is described. The proposed neuron leverages time-domain processing using voltage-controlled oscillators (VCOs) and a time-domain comparator to integrate the input spike and trigger the output spike. A novel leaky circuit uses a phase-locked loop (PLL) to drive the phase difference between the two VCOs toward zero. A weighted capacitive digital-to-analog converter (CDAC) synapse merges the input spikes and phase-frequency detector (PFD) outputs to generate the VCO control voltage. The neuron is implemented in a 28-nm CMOS technology and operates under a subthreshold supply voltage of 0.35 V. Occupying 154 μm2, measurement shows a maximum spike rate of 5.5 MHz and energy consumption of 159 fJ/spike.
22 February 2024 in IEEE Transactions on Circuits and Systems II: Express Briefs
VCO-based ADCs widely utilize coarse-fine readout to save power and hardware compared to counter-only converters. However, the timing mismatch due to the clock skew between the coarse and fine quantizers can lead to significant reconstruction errors. This paper proposes a digital calibration circuit to detect and correct coarse-fine timing mismatch for VCO-based ADCs. The circuit includes overcount/undercount logic to detect all possible timing mismatch cases and generates a correction value to digitally remove the errors. The calibration operates continuously in the background and is entirely digital, making it scaling-friendly and robust against analog imperfections. Simulations show that a VCO-based ADC utilizing the calibration circuit improves the SNR by 10.3 dB and 6.9 dB versus a conventional coarse-fine converter and one with a conventional retiming calibration, respectively.
1 January 2026 in IEEE Sensors Journal