25 November 2021 in IEEE Sensors Journal
EBEli Gabriel Avina Bravo
This study presents a low-power wearable system able to predict a fall by detecting a pre-impact condition, performed through a simple analysis of motion data (acceleration) and height of the subject. The system can detect a fall in all directions with an average consumption of 5.91 mA; i.e., it can monitor the activity of daily living (ADL), whether or not a fall occurs. The entire detection system uses a single wearable tri-axis accelerometer placed on the waist for the comfort of the wearer during a long-term application. The algorithm is based on the following hypothesis: “A region defined as balanced boundary circle, based on the user’s height, is characterized by the fact the chance that an actual fall happening is minimal. When an activity is classified outside this circle, an acceleration analysis is performed to determine an impending fall condition”. Our threshold-based algorithm was validated experimentally, first with 9 young healthy volunteers performing both normal ADL and fall activities and then using 10 ADL and 5 falls from public SisFall dataset. The results show that falls could be detected with an average lead-time of 259 ms before the impact occurs, with minimal false alarms (97.7% specificity) and a sensitivity of 92.6%. This is a good lead-time achieved thus far in pre-impact fall detection, permitting the integration of our detection system in a wearable inflatable airbag for hip protection.
9 March 2022 in Research, Society and Development
Numerous factors have contributed to the increase in waste production in large industries, among them steel and mining companies stand out due to their significant environmental impact, such as the pollution of terrestrial and aquatic environments, which has a direct influence on the reduction of the quality of life of local living beings. In this sense, this work investigated the feasibility of incorporating residues from the ornamental rock industry (known as abrasive sludge or RRO) in bentonite clay, aiming to achieve a viable technological route for use in the pelletizing of iron ore. The adopted methodology consisted of the chemical and physicochemical characterization of bentonite in its original state and the incorporation of ornamental rock tailings into bentonite by the following analyses: FRX, DRX, pH, moisture, apparent and absolute density. Subsequently, a statistical analysis of the ideal percentage of incorporation was carried out using the central composite rotational design method. The studied developments were evaluated based on the parameters adopted by Companhia Vale do Rio Doce (CVRD). From the FRX and XRD data, the samples were classified as silico-aluminous, adding more than 70% Si2O + Al2O3 and exhibiting a significant presence of quartz. The compositions that best met the value required by CVRD in relation to pH were four B20 samples, satisfying the basicity condition equal to at least 9.5. For bulk density, B30 presented 940.70 kg.m-3, a value close to the expected (961.20 kg.m-3), whereas for absolute density, two B20 samples showed better results: 2.55 and 2.58 for a benchmark of 2.4 to 2.5.
30 March 2021 in Brazilian Journal of Production Engineering
O processamento de rochas ornamentais promove a geração constante de lama abrasiva que, por sua vez, ocasiona diferentes tipos de contaminação. A possibilidade de reutilização dos resíduos gerados em processos industriais apresenta vantagens econômicas, portanto, é necessário conhecer as propriedades físicas, químicas e minerais desses resíduos. Sendo assim, o objetivo dessa pesquisa foi avaliar as possibilidades de aplicação da lama abrasiva, geradas em indústrias localizadas na cidade de Campina Grande – PB, tomando como base suas características principais. A metodologia consistiu nas seguintes análises: fluorescência de raios X, difração de raios X, microscopia eletrônica de varredura, análise de tamanho de partículas e análise físico-química. Análises químicas revelaram que os resíduos possuem características interessantes, principalmente para uso na construção civil. A análise mineralógica indicou que a amostra possui uma composição mineral essencial para a indústria cosmética, o que foi confirmado pelos elementos detectados presentes. O estudo do tamanho das partículas caracterizou a amostra como material de forma irregular e com boa micronização, confirmando o potencial de reutilização como cosmético, enquanto a análise morfológica mostrou a presença de ferro como fator limitante para determinadas aplicações. Testes físico-químicos confirmaram as características comuns à lama abrasiva. As amostras caracterizadas apresentaram, de forma geral, propriedades satisfatórias no que diz respeito a sua utilização como material alternativo em diferentes segmentos.