27 January 2020 in IEEE Transactions on Applied Superconductivity
9 January 2018 in IEEE Transactions on Applied Superconductivity
(RE)BCO commercial coated superconductors have been gaining an increasing interest due to the potentialities of using them in high-field magnets. The leading project is the 32 T user magnet recently tested successfully at full field at the NHMFL, Florida, USA. This state-of-the-art high field all-superconducting magnet, bath-cooled at 4.2 K, is comprised of a two-nested-coil insert pancake-wound with (RE)BCO tapes supplied by SuperPower Inc. and a multi-coil LTS outsert. To ensure the magnet reliable operation, it is important to estimate the hysteresis losses. Such an estimate will allow implementing safe operational procedures to avoid premature quenching and, in the worst case scenario, the insert failure. The insert coils have thousands of turns, with notable variations in the critical current. Therefore, estimating the losses in such a large superconducting magnet presents a significant challenge. We propose here a new approach relying on a multi-scale scheme to achieve a high computational efficiency. This new method is flexible enough to simulate different sections of the entire insert with the right level of detail while providing a larger computational speed than other approaches using the finite element method. Estimates of the hysteresis losses in the insert coils for a ramping operation sequence are presented.
31 March 2021 in IEEE Transactions on Applied Superconductivity
Magnetic stress is of particular concern for ultra high field magnets, especially, peak hoop stress of those magnets may be locally concentrated by the screening current stress (SCS). For instance, the Little Big Coil (LBC), which was designed, constructed, and operated by a collborate team led by NHMFL, generated the world record magnetic field of 45.5 T, but the conductor in LBC experienced plastic deformation due to excessive SCS. In this paper, to further analyze details of the mechanical stress behavior of LBC magnet, the effect of friction coefficient and overband radial build on stress alleviation is investigated by the parametric study. First, total current density with screening current is calculated by using the H-formulation together with domain homogenization method. Later, the entire magnet structure is modeled by the 2D finite element method to represent preload and axial interactions between each adjacent single pancake (SP), and 3 turns are assumed to be one engineering turn with frictionless radial turn-to-turn contact. While, friction acts between the coil and spacer in a direction that limits the radial displacement. Finally, we discuss the effects of friction coefficient and overband thickness by sweeping those parameters. Our parametric study implies that both friction and overband radial build can reduce peak hoop stress levels of LBC, however, effect of friction is dominant when overbanding is thicker than 0.5 mm.
16 June 2008 in Superconductor Science and Technology
We report on a first implementation of a design which provides a significant reduction of AC losses in YB2Cu3O7−δ (YBCO) coated conductors (CCs) without mechanical twisting. The conductor is composed of two diffusively bonded silver clad commercial CCs with zigzag patterned filaments partially separated by a dielectric layer. We produced three fully bonded samples with 500 μm wide filaments using three-stage photolithography and wet chemical etching. A tenfold reduction of AC losses at frequencies between 20 and 400 Hz was observed, while transport measurements and magneto-optical imaging showed no degradation of Tc and a low contact resistance of � 10−8 � cm2 between Ag and YB2Cu3O7−δ. (Some figures in this article are in colour only in the electronic version)
2 February 2018 in IEEE Transactions on Applied Superconductivity
Double disordered (DD) HTS layers processed via high fluence PLD with modulated pressure and barium zirconate precipitation yield very high engineering current densities, above 900 and 600 A/mm2 at 18 and 31 T, respectively, measured at 4.2 K and B||c. Tape architecture is based on 50-100 μm thick polished stainless steel tape which prior to DD-HTS deposition was coated with YSZ template yielding a biaxial in-plane texture with FWHM = 10-11 characterized using phi-scan XRD technique. High-resolution nano-structural analysis indicated a number of non-usual features in DD YBCO layers regarding “firework”-like ori-entation of nano-precipitations /nano-chains. These new features result in a very high concentration of local defects which reduce the critical current (Ic) measured at 77 K, self-field to about 30 % of the corresponding Ic in non-DD YBCO, and simultaneously lead to substantial gaining of Ic at high fields. The main result is a substantial improvement of Ic and engineering current density (Je) achieved at high field and liquid Helium temperature in long length, large area tapes with 4 and 12 mm width. Je above 970 A/mm2 at 4.2 K, B = 18 T, B||c was achieved in 12 mm wide tape.
27 September 2024 in Superconductor Science and Technology
Low-inductance, high-field insert solenoid magnets and 20 T dipole magnets for particle accelerators require flexible cables, wound from high-temperature superconductors (HTS) such as RE-Ba2Cu3O7− δ (REBCO) coated conductors, that allow bending to a 20 mm radius without significant degradation in performance. They require an operating current of at least 5 kA and a high engineering current density (J e) exceeding 500 A mm−2 at 20 T. HTS cable technologies that target such demanding magnet applications so far have not been able to meet the combination of these requirements. Here we present the development of the next generation of Conductor on Round Core (CORC®) wires that are produced with an optimized manufacturing process that improves their bending flexibility by factor of more than 2 compared to previous generation CORC® wires. CORC® wires now allow for a bending radius of 20 mm with only 2%–3% performance degradation. They allow bending to a radius of 15 mm with a performance retention of 83.5%. The performance of 30-tape CORC® wires wound from 2 mm wide REBCO tapes from SuperPower Inc, SuperOx and shanghai superconductor technologies was measured at magnetic fields up to 12 T. The overall performance at high magnetic fields of the next generation of CORC® wires improved by a factor of 1.5–1.8, depending on the REBCO tape manufacturer. CORC® wires wound from production REBCO tapes achieved a new record J e of 751 A mm−2 at a current of 8.3 kA at 12 T, and a J e of 530 A mm−2 at a current of 5.8 kA when extrapolated to 20 T. The next generation of CORC® wires present the first HTS cable technology that simultaneously meet the requirements on bending flexibility, engineering current density and critical current at 20 T for use in low-inductance, high-field particle accelerator magnets. They now enable a more expedited development of prototype low-inductance solenoid magnets that target fields exceeding 25 T and of accelerator magnets that generate a dipole field exceeding 20 T.