This article reports a 320-GHz low-jitter and low-reference-spur signal source consisting of an 80-GHz integer- $N$ phase-locked loop (PLL) and a 320-GHz frequency quadrupler. The 80-GHz PLL features a novel dual-path quadrature exclusive-OR (QXOR) technique to cancel the spurs at the reference frequency and its harmonics, enabling low-spur and low-noise phase locking. The proposed phase detector (PD) also enables frequency detection and lock detection (LD), rendering the band-searching to be decoupled from the loop components. Implemented in a 0.13- $\mu \text{m}$ SiGe BiCMOS technology, the proposed signal source shows a −73.1-dBc reference spur, −113.7-dB/Hz phase noise at 1-MHz offset at 40.96 GHz, and −90.3-dB/Hz phase noise at 1-MHz offset at 311.8 GHz. It achieves an integrated jitter of 66.9 fs rms at 40.96 GHz and 122 fs rms (both integrated from 10 kHz to 100 MHz) beyond 300 GHz, with a total division ratio of 512. The LD time is at the microsecond level. The maximum output power is −3.24 dBm, and the power consumption is 372 mW.
14 December 2021 in IEEE Journal of Solid-State Circuits
This article reports a channel-selection N-path passive low-noise amplifier (pLNA) featuring only switches, capacitors, and a step-up transformer (i.e. a SCT network) to build a highly linear, frequency-tunable, and high-Q bandpass response with in-band voltage gain and input-impedance matching. We also reveal the inductive and lowpass properties of the step-up transformer, composed of two vertically coupled spiral coils, for passband centering with the local oscillator (LO) frequency, and harmonic-folding reduction. Prototyped in 28 nm CMOS, a 4-path 20 MHz-bandwidth pLNA scores a 9.8 dB voltage gain and a 3.4–4.8 dB NF over a 1.7–3.6 GHz range. At 3 GHz, the out-of-band (OB)-IIP 3 measures +23.5 dBm, and the 3rd-harmonic-folding rejection ratio (HFRR 3 ) is 33 dB. With a blocker applied at the 80 MHz offset, the blocker −1 dB compression point ( $\text{B}_{-1\,\text {dB}}$ ) attains +1.7 dBm, and the blocker NF only raises moderately to 4.7 dB up to a 0 dBm blocker power. The only dynamic power comes from the four-phase 25%-duty-cycle LO generator that consumes 17.8–38.2 mW between 1.7 and 3.6 GHz. The entire pLNA occupies a 0.84 mm 2 die area.
3 August 2021 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper describes a low-power multiband blocker-tolerant receiver (RX) with three steps of filtering among two transconductance (Gm) stages. To consistently achieve low noise figure (NF) and high linearity over a wide range of operating frequency, a single-Gm low-noise amplifier (LNA) heads the RX with embedded N-path filtering, and feed-forward out-of-band (OB) blocker cancellation to surmount the tradeoff between the passband bandwidth (BW) and OB rejection without sacrificing the power budget. A filtering-by-aliasing (FA) block embeds another single-Gm baseband (BB) amplifier to allow a steep roll-off lowpass response with a clock-rate-defined passband BW. Prototyped in 28-nm CMOS, the RX achieves a 3.1-dB NF and a 5.4-dBm OB-IIP3 at 2 GHz, while consuming only 22 mW, measured at a gain of 22 dB. The tunable passband BW is 2.5 to 20 MHz, and the RF-to-BB composite filtering slope is 20 to 50 dB/10 MHz at 1.75xBW offset. The RX occupies a 0.24 mm2 active area.
1 September 2022 in IEEE Journal of Solid-State Circuits
This article reports an ultra-low-power (ULP) Bluetooth low-energy (BLE) receiver with an improved spurious-free dynamic range (SFDR). It features two passive-intensive RF techniques: an $N$ -path passive balun-LNA and a pipeline down-mixing baseband (BB)-extraction scheme. They together offer a high- $Q$ bandpass response at RF, and a high passive gain to suppress the noise of the BB hybrid complex filter. Specifically, the balun-LNA is a step-up triple-coil transformer aided by an $N$ -path switched-capacitor (SC) network to perform in-band voltage amplification, high- $Q$ bandpass filtering, $I$ / $Q$ down-mixing, and input-impedance matching. Instead of using active amplifiers as the first-BB gain stage, we passively extract the four-phase ( $I$ / $Q$ and differential) BB signals using a pipeline of passive-SC networks that can stack up the voltage gain. Prototyped in TSMC 28-nm CMOS, the BLE receiver consumes only 266 $\mu$ W, of which 75 $\mu$ W in the BB hybrid filter at 1 V, and 191 $\mu$ W in the LO divider $+$ buffer at 0.6 V. Measured at the maximum RF-to-BB gain of 61 dB, the receiver exhibits a noise figure (NF) of 6.1 dB and an out-of-band (OOB)-IIP $_{3}$ of 22.5 dBm. The corresponding SFDR is 77 dB for a 1-MHz BLE channel and a 10-dB minimum signal-to-noise ratio (SNR $_{\mathrm{min}})$ . The OOB-B $_{{-\text{1\,dB}}}$ is $-$ 3 dBm.
16 August 2019 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper describes a wideband ultra-fast-settling fractional-N bang-bang digital phase-locked loop (DPLL) for multi-ISM-band ultra-low-power (ULP) radios. We propose a mismatch-free digital-to-time-converter (DTC) gain calibration scheme to effectively shorten the calibration time, while the split coarse-fine PLL loops with different loop bandwidths accelerate the loop settling speed. The employed ring VCO (RVCO) aids to extend the frequency tuning range and generate multi-phase outputs. Prototyped in 65-nm CMOS, the DPLL consumes 1.2–2.4 mW over a wide frequency locking range of 68.3% (1.3–2.65 GHz) and occupies a die area of 0.12 mm 2 . The settling time measures $8~\mu \text{s}$ at an 82-MHz initial frequency error.
22 September 2020 in IEEE Journal of Solid-State Circuits
This article reports a multiband frequency-division duplex (FDD) SAW-less transmitter (TX) for 5G new radio (5G-NR). It features a bandwidth-extended N-path filter-modulator (BW-Ext FIL-MOD) to enable high-Q bandpass filtering at a flexible RF and the synthesis of a complex-pole pair via merging positive- and negative-feedback networks (PFN/NFN) enhances its bandpass characteristic, surmounting the tradeoff between the passband flatness and out-of-band (OB) rejection, a switched-baseband (BB) input network to avoid the mutual loading effect between the BW-Ext FIL-MOD and itself, and a transimpedance amplifier (TIA)-based power-amplifier driver (PAD) to absorb both the bias and signal currents of the BW-Ext FIL-MOD for better linearity and power efficiency. Fabricated in 28-nm CMOS, the proposed TX manifests a 20-MHz passband BW and a consistently low OB noise (≤-157.5 dBc/Hz) for different 5G-NR bands between 1.4 and 2.7 GHz. The TX achieves sufficient output power (3 dBm), high TX efficiency (2.8%-3.6%), and high linearity (ACLR₁ < 44 dBc and EVM < 2%). The active area is 0.31 mm².