6 June 2019 in Journal of Lightwave Technology
We have developed three-dimensional object profiling system using a highly accurate FMCW optical ranging system. A DFB laser and a VCSEL are used as the laser source and the optical frequency is swept by the injection current modulation with a symmetric triangular wave. The influence of nonlinearity in the optical frequency sweep is canceled by utilizing k-sampling technique. Since the optical frequency sweep range of a VCSEL is larger than that of a DFB laser, high spatial resolution and high ranging accuracy are achieved by using a VCSEL. The spatial resolution evaluated by the full-width at half maximum (FWHM) is $460\,\mu \rm{m}$ and the standard deviation of the ranging accuracy is σ = 2.7 μm when a VCSEL is used as the frequency-swept laser source, and the FWHM is 2.3 mm and σ = 14.8 μm when a DFB laser is used as the frequency-swept laser source. Accordingly, fine and clear object profiling of a coin and a printed circuit board is achieved by using a VCSEL as the frequency-swept laser source. Finally we speed-up the measurement time by increasing the repetition frequency of the injection current modulation and optimizing timing of the data acquisition, the galvano mirror scan and the FFT analysis by taking account of the transient response of the galvano mirror, and the fastest measurement time of 22.6 sec is achieved for 201 × 201 points measurement points, which is four times faster than our previous results. We also discuss the effect of moving average filtering and median filtering to improve profiling quality.
9 January 2023 in IEEE Transactions on Instrumentation and Measurement
Time of Flight (ToF) Lidar range finder is widely used in various applications such as automotive driving, marine environment surveying, atmospheric observing, and physical distancing monitoring. The ToF Lidar offers a high-resolution range, which can be achieved by increasing the modulation frequency. However, when the modulation frequency is increased, the maximum unambiguous range tends to decrease. To overcome such a problem, we develop a novel ToF Lidar range finder based on dual-modulation frequencies switching, capable of providing an extended range while maintaining the high-resolution. In the design, the modulation frequency is alternately changed between 2 MHz and 10 MHz to modulate the intensity of the laser diode as a transmitter. We operate an avalanche photodetector as a receiver to obtain a reflection of modulated light from a target. By switching between dual-modulation frequencies, the photodetector detects two-phase shifts, which are calculated by our phase-shift algorithm. It is shown that the proposed algorithm can solve the ambiguous range problem. As proof of the concept, we experimentally demonstrate a range measurement of a target up to 55 m distance, where the ambiguous range is experienced four times if only a single modulation frequency of 10 MHz is used. Interestingly, the range ambiguity no longer appears after applying the proposed design and algorithm.
1 January 2016 in AIP Conference Proceedings
RPRetno Wigajatri Purnamaningsih
Retno Wigajatri Purnamaningsih
In general, Fiber Bragg Grating (FBG) sensor works based on observation of spectral response characteristic to detect the desired parameter. In this research, we studied intensity response characteristic of FBG to detect the dynamic strain. Experiment result show that the reflected intensity had linier relationships with dynamic strain. Based on these characteristics, we developed the FBG sensor to detect low frequency vibration. This sensor is designed by attaching the FBG on the bronze cantilever with dimensions of 85×3×0.5 mm. Measurement results showed that the sensor was able to detect vibrations in the frequency range of 7-10 Hz at temperature range of 25-45 ˚C. The measured frequency range is still within the frequency range of digging activity, therefore this vibration sensor can be applied for oil pipelines vandalisation detection system.
10 April 2017 in Journal of Physics: Conference Series
The road damage due to excessive load is one of the causes of accidents on the road. A device to measure weight of the passing vehicles needs to be planted in the road structure. Thus, a weight sensor for the passing vehicles is required. In this study, we designed a weight sensor for a static load based on a power loss due to a micro bending on the optical fiber flanked on a board. The following main components are used i.e. LED 1310 nm as a light source, a multimode fiber optic as a transmission media and a power meter for measuring power loss. This works focuses on obtaining a suitable deformer design for weight sensor. Experimental results show that deformer design with 1.5 mm single side has level of accuracy as 4.32% while the design with 1.5 mm double side has level of accuracy as 98.77%. Increasing deformer length to 2.5 mm gives 71.18% level of accuracy for single side, and 76.94% level of accuracy for double side. Micro bending design with 1.5 mm double side has a high sensitivity and it is also capable of measuring load up to 100 kg. The sensor designed has been tested for measuring the weight of motor cycle, and it can be upgraded for measuring heavy vehicles.
26 December 2024 in EUREKA: Physics and Engineering
Soliton waves are self-reinforcing solitary waves that maintain their shape while traveling at a constant velocity, making them particularly useful in numerous optical applications. This research focuses on observing the phenomenon of soliton waves in tin dioxide (SnO2) to model the propagation of electromagnetic waves in both spatial and time domains. The FDTD method is well-suited for this type of study because it allows for the numerical analysis of electromagnetic wave propagation by solving Maxwell's equations over discrete time and space grids. One of the primary challenges in simulating wave propagation in materials like SnO2 is accounting for dispersive effects and nonlinearities. Therefore, this study aims to augment the FDTD approach with Z-transformation techniques, allows for an efficient formulation of dispersive and nonlinear effects, thus enhancing the computational efficiency and accuracy of the simulations. The simulation results show that soliton waves can form in the optical material of SnO2 when an electric field exceeding 0.8 V/m is applied. The formation of soliton waves in SnO2 is primarily attributed to the nonlinear properties of the material. The simulation demonstrates that SnO2 exhibits significant nonlinear behavior conducive to soliton formation. The dispersive properties of SnO2 also play a crucial role in the formation and stability of soliton waves. Dispersive effects can cause wave packets to spread out, but in the presence of nonlinearity, these effects can be balanced, forming stable solitons. In conclusion, this study provides a foundational understanding of soliton wave formation in SnO2, highlighting its potential for various optical applications