Time of Flight (ToF) Lidar range finder is widely used in various applications such as automotive driving, marine environment surveying, atmospheric observing, and physical distancing monitoring. The ToF Lidar offers a high-resolution range, which can be achieved by increasing the modulation frequency. However, when the modulation frequency is increased, the maximum unambiguous range tends to decrease. To overcome such a problem, we develop a novel ToF Lidar range finder based on dual-modulation frequencies switching, capable of providing an extended range while maintaining the high-resolution. In the design, the modulation frequency is alternately changed between 2 MHz and 10 MHz to modulate the intensity of the laser diode as a transmitter. We operate an avalanche photodetector as a receiver to obtain a reflection of modulated light from a target. By switching between dual-modulation frequencies, the photodetector detects two-phase shifts, which are calculated by our phase-shift algorithm. It is shown that the proposed algorithm can solve the ambiguous range problem. As proof of the concept, we experimentally demonstrate a range measurement of a target up to 55 m distance, where the ambiguous range is experienced four times if only a single modulation frequency of 10 MHz is used. Interestingly, the range ambiguity no longer appears after applying the proposed design and algorithm.
1 October 2022 in Indonesian Journal of Electrical Engineering and Computer Science
In this paper, we investigate a hexagonal two-layer photonic crystal fiber based on surface plasmon resonance (HT-PCF-SPR) which is easy to fabricate as a sensor for detecting the refractive index of analytes. After performing numerical simulations using COMSOL multiphysics based on the finite element method (FEM), it was found that the HT-PCF-SPR could detect the analyte's refractive index in the range 1.34-1.37 RIU and in the wavelength range from 730 nm to 810 nm. The plasmonic material used in the design is gold with a thickness of 40 nm which is located outside the layer and in two opposite air holes in the core. The HT-PCF-SPR design has good performance in detecting analytes, it is found that the sensitivity in detecting analytes is 2,000 nm/RIU, meaning that every 1 RIU shift of analyte shifts the wavelength by 2000 nm. Meanwhile, the sensor resolution obtained from the design is 6.67×10-5 RIU, and it is found that the larger the air hole, the greater the confinement loss value.
Optical power is one of the important parameters in optics. Optical power is used to determine losses that occur along the optic link. Optical power is also needed in the designing optical fiber sensors. In this research, design of signal-conditioning-circuit and optical-power-measurements characterization for laser at wavelength 1310 nm and 1552 nm have been conducted. This device works as an optical power meter. It uses 6 units of resistances (100 Ω, 1k Ω, 10k Ω, 100k Ω, 1M Ω and 10M Ω) as feedback of transimpedance amplifier. These resistors are connected in parallel and combined to expand the measurement range of optical power. The obtained data were compared and validated with Anritsu ML9002A OPM. The result was 5 different optical power measurement regions for each wavelength from -5 dBm to -45 dBm. This range can be expanded using analytical approach to obtain a wider dynamic range.
1 December 2023 in Bulletin of Electrical Engineering and Informatics
In this paper presents a numerical simulation using the finite element method (FEM) to analyze the performance of a photonic crystal fiber (PCF) integrated with plasmonic material sensor components. The sensor comprises silica and Au layers with a thickness of 45 nm, arranged in a simple geometric structure. Our proposed sensor component exhibits ultra-low loss, distinguishing it from previous studies that have focused on wavelength-sensitive (WS) and amplitude-sensitive (AS) measurement techniques. The refractive index (RI) range of the sensor component spans from 1.32 to 1.38 RIU. The maximum WS and AS values achieved are 6,000 nm/RIU, -373.4 1/RIU (x-polarization), and -385.4 1/RIU (y-polarization), respectively. Moreover, we demonstrate an ultra-low loss of 0.00117 dB/cm (x-polarized) and 0.00307 dB/cm (ypolarized). In terms of sensor resolution, this design achieves a remarkable resolution of 1.6×10-7 RIU for both x-and y-polarized measurements
1 July 2024 in Instrumentation Science & Technology
This study presents the application of fiber bragg grating (FBG) sensors coated with polyimide for detecting carbon dioxide (CO₂) gas, employing both theoretical and experimental approaches. The basic FBG components were coated with polyimide layers of varying thicknesses. Subsequently, the fabricated FBG sensors were characterized using an optical interrogator system with four channels. Furthermore, the sensor was tested for CO₂ detection at a working temperature of 47 °C. Experimental data showed that the FBG sensor coated with polyimide layers of 10 nm, 15 nm, and 20 nm demonstrated sensitivities of 1.9 ppm, 1.84 ppm, and 1.8 ppm, respectively. In contrast, the uncoated FBG sensor exhibited a higher sensitivity of 3 ppm. Increasing the coating thickness beyond 20 nm leads to a decrease in sensor sensitivity. The findings suggest that an optimal polyimide coating thickness for CO₂ detection using FBG sensors is around 20 nm. Achieving high sensitivity in CO₂ gas sensors is crucial for their effective use across a broad range of applications.