9 March 2022 in IEEE Journal on Selected Areas in Communications
Enabling pervasive WiFi devices with non-contact sensing capability is an important topic in the field of integrated sensing and communication. Doppler effect has been widely exploited to estimate targets’ velocity from wireless signals. However, the separation of signal sources and receivers complicates the relationship between Doppler frequency shift (DFS) and target velocity in WiFi-based non-contact sensing systems. In contrast to existing works that rely on either approximated relations or coarse-grained information such as whether a target is moving toward or away from WiFi transceivers, this paper investigates rigorously the dependency of velocity estimation accuracy on target locations and headings in WiFi sensing systems. The theoretical insights allow us to derive a closed-form solution and understand the fundamental limitation of velocity estimation. To optimize velocity estimation performance, we devise a receiving device selection scheme that dynamically chooses the optimal set of receivers among multiple available WiFi devices. A prototype real-time target tracking system has been implemented using commodity WiFi devices. Extensive experimental results show that the proposed system outperforms state-of-the-art approaches in velocity estimation and tracking, and is able to achieve $9.38cm/s$ , 13.42°, $31.08cm$ median errors in speed, heading and location estimation amongst experiments conducted in three indoor environments with three device placements and eight human subjects over 15 trajectories.
27 March 2023 in Proceedings of the ACM on Interactive, Mobile, Wearable and Ubiquitous Technologies
Falls are the leading cause of fatal injuries to elders in modern society, which has motivated researchers to propose various fall detection technologies. We observe that most of the existing fall detection solutions are diverging from the purpose of fall detection: timely alarming the family members, medical staff or first responders to save the life of the human with severe injury caused by fall. Instead, they focus on detecting the behavior of human falls, which does not necessarily mean a human is in real danger. The real critical situation is when a human cannot get up without assistance and is thus lying on the ground after the fall because of losing consciousness or becoming incapacitated due to severe injury. In this paper, we define a life-threatening fall as a behavior that involves a falling down followed by a long-lie of humans on the ground, and for the first time point out that a fall detection system should focus on detecting life-threatening falls instead of detecting any random falls. Accordingly, we design and implement LT-Fall, a mmWave-based life-threatening fall detection and alarming system. LT-Fall detects and reports both fall and fall-like behaviors in the first stage and then identifies life-threatening falls by continuously monitoring the human status after fall in the second stage. We propose a joint spatio-temporal localization technique to detect and locate the micro-motions of the human, which solves the challenge of mmWave's insufficient spatial resolution when the human is static, i.e., lying on the ground. Extensive evaluation on 15 volunteers demonstrates that compared to the state-of-the-art work (92% precision and 94% recall), LT-Fall achieves zero false alarms as well as a precision of 100% and a recall of 98.8%.
28 March 2024 in IEEE Transactions on Mobile Computing
Although WiFi-based contactless sensing has made significant progress in the past decade, most prior work still focus on the reflection zone far from WiFi transceivers, while few studies explore the diffraction zone near transceivers. Additionally, previous diffraction models only consider the CSI amplitude signal and ignore the impact of multipath. In this work, we develop an accurate diffraction model to characterize the relationship between both CSI amplitude and phase and target's movement in the diffraction zone. We further put forward the deformation forms of the model under static multipath conditions and find that the CSI patterns vary significantly with multipath. Consequently, the common assumption of a one-to-one mapping between CSI patterns and activities in existing work fails due to multipaths, degrading sensing performance when multipath changes. To address this challenge, we propose to extract a relative change pattern from CSI signals to recover the one-to-one mapping relations and eliminate the impact of static multipath. Extensive experiments under various multipath conditions demonstrate an accuracy higher than 96% for the coarse-grained intrusion detection and an average error rate of 0.6 bpm for the fine-grained respiration monitoring.
12 June 2023 in Proceedings of the ACM on Interactive, Mobile, Wearable and Ubiquitous Technologies
In the past few years, a large range of wireless signals such as WiFi, RFID, UWB and Millimeter Wave were utilized for sensing purposes. Among these wireless sensing modalities, WiFi sensing attracts a lot of attention owing to the pervasiveness of WiFi infrastructure in our surrounding environments. While WiFi sensing has achieved a great success in capturing the target's motion information ranging from coarse-grained activities and gestures to fine-grained vital signs, it still has difficulties in precisely obtaining the target size owing to the low frequency and small bandwidth of WiFi signals. Even Millimeter Wave radar can only achieve a very coarse-grained size measurement. High precision object size sensing requires using RF signals in the extremely high-frequency band (e.g., Terahertz band). In this paper, we utilize low-frequency WiFi signals to achieve accurate object size measurement without requiring any learning or training. The key insight is that when an object moves between a pair of WiFi transceivers, the WiFi CSI variations contain singular points (i.e., singularities) and we observe an exciting opportunity of employing the number of singularities to measure the object size. In this work, we model the relationship between the object size and the number of singularities when an object moves near the LoS path, which lays the theoretical foundation for the proposed system to work. By addressing multiple challenges, for the first time, we make WiFi-based object size measurement work on commodity WiFi cards and achieve a surprisingly low median error of 2.6 mm. We believe this work is an important missing piece of WiFi sensing and opens the door to size measurement using low-cost low-frequency RF signals.
19 December 2023 in Proceedings of the ACM on Interactive, Mobile, Wearable and Ubiquitous Technologies
Millimeter wave (mmWave) radar excels in accurately estimating the distance, speed, and angle of the signal reflectors relative to the radar. However, for diverse sensing applications reliant on radar's tracking capability, these estimates must be transformed from radar to room coordinates. This transformation hinges on the mmWave radar's location attribute, encompassing its position and orientation in room coordinates. Traditional outdoor calibration solutions for autonomous driving utilize corner reflectors as static reference points to derive the location attribute. When deployed in the indoor environment, it is challenging, even for the mmWave radar with GHz bandwidth and a large antenna array, to separate the static reference points from other multipath reflectors. To tackle the static multipath, we propose to deploy a moving reference point (a moving robot) to fully harness the velocity resolution of mmWave radar. Specifically, we select a SLAM-capable robot to accurately obtain its locations under room coordinates during motion, without requiring human intervention. Accurately pairing the locations of the robot under two coordinate systems requires tight synchronization between the mmWave radar and the robot. We therefore propose a novel trajectory correspondence based calibration algorithm that takes the estimated trajectories of two systems as input, decoupling the operations of two systems to the maximum. Extensive experimental results demonstrate that the proposed calibration solution exhibits very high accuracy (1.74 cm and 0.43° accuracy for location and orientation respectively) and could ensure outstanding performance in three representative applications: fall detection, point cloud fusion, and long-distance human tracking.